Car wont Boot more..

[[[d a n n y]]]

i think my car was problems...

my car wont boost higher than 0.6bar boost (factory GTR boost)

i've removed the restrictor and put in a b/c controller (bleed valve system) and it still wont boost past 0.6bar boost...

what's going on

does any1 have any ideas?

ps..i had an engine rebuild it boosted to 1bar b4 but after that it doesnt...

[SKYZER 33]

]']i think my car was problems...

my car wont boost higher than 0.6bar boost (factory GTR boost)

i've removed the restrictor and put in a b/c controller (bleed valve system) and it still wont boost past 0.6bar boost...

what's going on

does any1 have any ideas?

ps..i had an engine rebuild it boosted to 1bar b4 but after that it doesnt...

What sort of boost controller you got? i had a turbo smart boost controller and had the same problem as you. so i took apart the bleed valve gave it a good clean mine was full of crap which stopped it from working properly.

[LANFOH]

Check all your hoses and make sure there isnt a leak somewhere then try winding the bleeder both ways and testing it. Cant see why it wouldnt work unless the bleeder has been installed wrong?

[[[d a n n y]]]

ok here's how to stroy goes..

currently it doesnt have any1 boostcotrollers and it still wnt boost past 0.6

even with the restrictor washer off..

i dont think the b/c is the problem here..

b4 my engine rebuild the car was boosting to 1bar without the restrictor..

but now it's not.

[[[d a n n y]]]

plz any1 help me?

[[[d a n n y]]]

bump plz help

[Roy]

So when your engine was rebuilt were there any mods done that would help the engine breath?

Are yoou still running a cat? How old is it? .... at 0.6bar does the car feel its down on power? How are you measuring the 0.6bar, aftermarket gauge?

[paulR32gtr]

Whoever installed the rebuilt engine may not have re-connected the line that sends to the stock solenoid / your boost controller. Maybe they blocked up the outlet so you are on low boost until the engine is completely run in?

[[[d a n n y]]]

well the eingines done 15K atm..

it's been bored out to 2.8L forged internals ported head and so on

i have a Nismo cat..on my car.

plz expalin more about the outlet plz

[Boosting]

I had the same porblem insted of putting the bleed valve where the factory solinoid is try hooking it up straight to the actuators on he other side thats what i did works fine

[[[d a n n y]]]

mate would u give me more info about that? plz?

[[[d a n n y]]]

bump plz help

[paulR32gtr]

There is a vacuum diagram in the R32 GTR manual that shows the stock boost control solenoid and how it hooks up, as well as how the stock actuators are fed boost. This would be best for you to trace how it is supposed to be set up. Lwells has posted a copy of this manual in general maint. section - download quick! Otherwise search on the net for it.

It sounds like the person that installed your engine has blocked the pipe that the stock solenoid uses to bleed air off the boost feed to the actuators.

The only way is to get that diagram, understand how it needs to work, then go and look under your bonnet.

Paul

[[[d a n n y]]]

There is a vacuum diagram in the R32 GTR manual that shows the stock boost control solenoid and how it hooks up, as well as how the stock actuators are fed boost. This would be best for you to trace how it is supposed to be set up. Lwells has posted a copy of this manual in general maint. section - download quick! Otherwise search on the net for it.

It sounds like the person that installed your engine has blocked the pipe that the stock solenoid uses to bleed air off the boost feed to the actuators.

The only way is to get that diagram, understand how it needs to work, then go and look under your bonnet.

Paul

cheers mate

ur a good man