Jump to content
SAU Community

Track whores!! - show us your bonnet restraint!


Recommended Posts

Hi guys, having been off work for the last 2 days from illness, and generally going mad watching day time TV, I sat down and devised what I think is a good secondary bonnet restraint for track days.

Basically, one end is hooked into the bonnet in holes next to the bonnet latch. The wire is secured through two washers, one of which has a few holes drilled through. The wire is threaded through as in the pics, and a bolt holds the two washers together. The end that attaches to the bonnet is secured with a wing nut, to aid getting the thing on and off.

The other end of the strap is configured in the same manner, only it is secured by a nut rather than a wing nut. This end is hooked onto one of your tow hooks via a carabena.

If anyone wants them I can supply without the carabena for $15 or so :(

Tell me what you think or show me what you've got!

Cheers

BonnetStrap0003.JPG

BonnetStrap0002.JPG

BonnetStrap0001.JPG

For those of us who still have no clue how this works and for what.. can you explain further? :)

Basically, when you hit the track, you are almost always required to have a secondary bonnet restraint apart from your ordinary latch.

Bonnet pins are an option, but for a street car they are illegal (protrusions) and defectable.

The restraints I was previously using were difficult to use, so I thought this was a better solution.

When you open your bonnet, there are a series of holes on either side of the bonnet latch. For this restraint, you undo the end with the wing nut, open the end of the hook and thread it through two of these holes. The reassemble through the washer and fasten down the cable with the wing nut.

When you close the bonnet, the restraint will drop down in front of the radiator, then you just latch the other end of the restraint to one of the tow hooks using the carabena

Too easy :(

Here, get this up ya's, impatient buggers.

I used nylon coated steel wire rope of about 5 mm diameter using bulldog clamps on each loop. Then a stainless crab to join.

I will be installing the aerocatches when Nelly isn't looking ....shhh :P

That's what I was running, but found that my bonnet wouldn't shut properly... and basically the one denham made for my car was too short - so to get in there and do it up you needed hands of a gypsie / pikie...

ps show us the turb's side!!

Ronin 09: The restraints that Geoff has shown you have been used on Archie's silver R32 GTR and it opened and shut fine. You do need to leave a little slack to reach in. The restaints are not there to stop the bonnet opening, they are only ment to stop the bonnet from hitting the windscreen and covering your vision. So having the restaints long enough to open the bonnet about 40cm should be perfect.

Strange but true- we've gotten away with using one of those webbed belts you pick up at Just Jeans for about 10 bucks :D

hehehe works on rental cars too.

i used a piece of boring old hemp rope at bathurst a few years back too

It doesn't have to be sexy, hell it may not even have to work....just has to be there.

  • 3 weeks later...

Hey , i hadnt seen these photos:)

The twin setup looks good, see that tape came in handy:thumbsup:

Geoff_TT_RB25.jpg

... and the new GTR bar... fark it you were so close to getting the thing to the track with grunt, susp, cooling and borrowed rubber:)

Will you still be around for Sandown in June, only i wont have any spare rubber to lend you, im using it like its going out of style:(

And who is that Malboro esq, stunning hunk of man meat....he must do all right with the girls:)

Geoffs_Place.jpg

Still not getting time for the car but I do intend to be here in June. May even have the wheels and rubber by then but a big thanks for the offer for Calder, just wish I'd got there.

That bar has come off to remake the mould and my new/replacement one is supposed to be Kevlar, with a vented Kevlar bonnet and maybe an undertray and splitter with Kevlar guards coming later. Mine is meant to be the demo car, but the guy making them was in a prang on the weekend where he broke his collarbone so a bit of a wait on the stuff.

As for the marlboro man....last sighted at Sandown grinning from ear to ear.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...