Jump to content
SAU Community

Recommended Posts

I think that this depends on what part of melbourne your talking about. Stay out of knox. One memeber from here was from WA with his WA registered car and WA license, mr TMU pulls him over and immideatly recognises that his 32gtst has an RB25 inside. The driver copped a red sticker because he had P plates and was over the power/weight ratio

The person who copped it was me. I had a R32 with a RB25DET.

The car was WA regoed and all, but they still recognised it and checked the engine block number and did me for no engineering.

I wouldnt do it, you cant fool them. If ur prepared to fork out a couple of grand go ahead and get the thing engineered. They will still **** u over in some way though with conversions.

I still don't know what the big deal with the crack down on engineering at the moment.. how many accidents have taken place where the cause of the car has been anything other than driver error in a modified car?

oh hum

If you have insurance, full comp.

And your car is butchered. If they check... bye bye insurance

Also, if you get canaried at any stage. A normal RWC place will check it.

If it dont match they wont pass you for a RWC and then you'll never get it engineered in time

I have *heard* that RB20, RB25 and RB26 cam covers are interchangable... so you might want to find yourself a nice set of second hand RB20 cam covers with a nice big "RB20" on the timing belt cover :O save the hassles. I would imagine they wouldn't bother checking the engine number if it had a RB20 cam cover.

The RB20/26 covers wouldn't fit on the RB25 unless you removed the VVT, which is half the appeal of the 25 to me (the extra 0.5L doesn't hurt either).

I was actually just thinking that there was an extra lump on the RB25 timing cover on the inlet side when I wrote that... LOL

But you could go the exposed cam wheel look with RB20 covers and an ECCS sticker on the plenum... sorted :D

Yeah, but how starionturbo was spotted was the plenum. well thats what he said in his post. The officer spotted it stright away eventhough he had the cam cover on and the big RB20 on the front.

Crap! just read that too! oops.

Are the plenums THAT different looking from the top?

I was actually just thinking that there was an extra lump on the RB25 timing cover on the inlet side when I wrote that... LOL

But you could go the exposed cam wheel look with RB20 covers and an ECCS sticker on the plenum... sorted :D

haha yeah, I actually ran the exposed cam wheel for a while. It's a good look :P

BTW That cop sure must have known his engines if he picked it from the plenum. I'd be fooled by the ECCS sticker :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
×
×
  • Create New...