Jump to content
SAU Community

Recommended Posts

hey guys this stuff has been sitting hesr since i sold my car and i dont need it anymore.

RB20DET Actuator. provides more boost than the rb25 actuator. $30

Cefiro intercooler standard. good condition, once again came off when i upgraded the cooler. $50

cheap boost controller bleed valve $20 used for a week or so.

6 Injectors from seres 2 rb20det. came outof my car when i upgraded the injectors they work fine just need new pintle caps. 270CC. about 72,000 ks on em. $50

injectors.jpg

RB20 AFM mesh removed only removed as i upgraded to a Z32$50

airflowmeter.jpg

1. Series 2 rb25 turbo compressor cover and compressor wheel.

2. TO4E V trim wheel i bought brand new to fit to an rb20/25 turb

3. metal exhaust gasket for rb20, 25 turbo dump

4. Silicon turbo hose 3" inches

$100 for all the turbo bits!!!

turbobits.jpg

1, take off your rb turbo and take your turbo, this compressor wheel and housing to a turbo place and say "machine this wheel and housing to fit this turbo.

GO HERE FOR TURBO INFORMATION

all prices are negotiable!!! and can be picked up from inner west sydney, or i will post to you

sonuds ok but you are in wa!!! postage would be like $10 and i would want $15 for it so you could prob buy one locally for that much and i would rather sell it to whoever buys the compressor as they will prob need a new gasket too.

but if after a day or so no one wants all the bits together its all yours :)

i will pm you in a couple o days

cheers!

is the bleed valve still for sale?

hey guys this stuff has been sitting hesr since i sold my car and i dont need it anymore.

RB20DET Actuator. provides more boost than the rb25 actuator. $30

Cefiro intercooler standard. good condition, once again came off when i upgraded the cooler. $50

cheap boost controller bleed valve $20 used for a week or so.

6 Injectors from seres 2 rb20det. came outof my car when i upgraded the injectors they work fine just need new pintle caps. 270CC. about 72,000 ks on em. $50

injectors.jpg

RB20 AFM mesh removed only removed as i upgraded to a Z32$50

airflowmeter.jpg

1. Series 2 rb25 turbo compressor cover and compressor wheel.  

2. TO4E V trim wheel i bought brand new to fit to an rb20/25 turb

3. metal exhaust gasket for rb20, 25 turbo dump

4. Silicon turbo hose 3" inches

$100 for all the turbo bits!!!

turbobits.jpg

1, take off your rb turbo and take your turbo, this compressor wheel and housing to a turbo place and say "machine this wheel and housing to fit this turbo.

GO HERE FOR TURBO INFORMATION  

all prices are negotiable!!! and can be picked up from inner west sydney, or i will post to you

OK i have now ansered 46 private messagea about the turbo stuff. and no one has bought it yet.

Its not like i am asking for a lot of money here the compressor wheel alone is worth $150.

and i am throwing in another compressor, a gasket, a compressor housing and some silicone tube!!!!!!!!!

somebody buy it or i will throw it in the bin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
    • Ah coolant overflow, previous discussions make way more sense now lol. 
×
×
  • Create New...