Jump to content
SAU Community

Recommended Posts

What would in your opinon be the cheapest way to build a 10 second car.

The only rules are:

- Cost of the 10 second car must substitute in the cost of the car and the mods.

- No major weight reduction mods

- No blown carburettored V8's

In my opinon I believe the GSR Lancer would be the best candidate for building a 10 second car as its a relatively cheap car to buy, 4wd and has an abundance of aftermarket kits to build on it.

Link to comment
https://www.sau.com.au/forums/topic/76558-cheapest-10-second-car/
Share on other sites

Old mazda 808 with a 13BT and old school T04, microtech, shortened 9inch, supra 5 speed and custom tailshaft with 8 inch slicks jammed under the rear end with some suspension work.

Total cost would be about 17k including car

Old mazda 808 with a 13BT and old school T04, microtech, shortened 9inch, supra 5 speed and custom tailshaft with 8 inch slicks jammed under the rear end with some suspension work.

Total cost would be about 17k including car

I am up with that for sure the cheapest way to build 10sec package is just the way hes said, but put a T66 (with large exaust wheel) on instead of the T04

Mate is almost finished with his 13bt in 1300 wagon with the large port work and the T66 i cant wait till its run in and i get to have a go

I know you mentioned no blown v8s but the cheapest is definately a vb or vc commodore.

-THe car= $1000 in pretty good cond

- Motor= $4000 308 with a stroker at least 355

- Tranny=$3000 tricked up manualised auto

-Diff= $2500 9 inch with 4 link setup

- Wheels/tyres and miscalaneous= $2500

All up $13000

ANd if you want to go injected, add another 2g.

But rotary was my second choice its just the base cars are worth alot these days!!!

yea i knew a guy with a rx2 with a 13b in it it wooda been near 10s and it was cheap for him motor was 6k worked off its tits then shell was just about nothing nothing

then he got a r100 and put the motor in that

other guy i know has a V8 in a Ford Capri its a ex drag car does 11's had huges wheels on the back and motor coming out the hood

if he superchargers it it will do 10's

Go the rotor in a lite car :cheers:

The other cheapish one would be a 1GGTE with a big turbo, good tune, in something small. The stock bottom ends are unreal. To get a bit more go out of them use a supercharged bottom end, as they are 0.5 compression ratio higher, and can still cop massive amounts of abuse. Full motor would be about $700-1000ish now?

But yeah, carby V8, cheap as, or Rotor. 10sec car isnt that hard, but a reliable street driveable one is a bit more of a trick.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...