Jump to content
SAU Community

THE (ONLY) DECA results/photos/experiences/reviews/recollections/brags thread


Recommended Posts

I love the one of you Roy where you just clip the cone.  Precision sideways....  or pure arse.

Pure arse as you can tell with the spin 2 seconds later...then again 5 seconds after that. I hate htose ones where you have greater then 90 deg to turn as i cant use the handbrake:(

Where is Geoff...teach me Obey-One :)

  • Replies 199
  • Created
  • Last Reply

Top Posters In This Topic

The clip posted is one of the last ones from that 'khana and I think that was Shiv ... thoough, it's all a bit of a blur now so don't take my word for it.

yep that was me getting chopped by the tree fiddy

I know DavidM (350Z @ DECA) has some footage - not sure of what though.

What I have is what I already posted. I do have more, but it's more of the same ie. no footage of the back-track or the slalom knock-out competition.

ps. Where's the 'gathering' going to held next Tuesday?

Anyone else from WRX or Fangers got some footage from this event.  I still need some good stuff from the back track.

I forgot my Camera, blame the early morning, altho my photography skills are as reliable as my driving so wouldn't help you much there either :rofl:

I'm waiting to see Joel's pics!

miniwog

I'm just upset/depressed/suicidal that no-one has any footage of the TX5 giving Aaron a run for his money.

Send me a PM with your e-mail and I'll e-mail you a clip of the TX5 dodging the cones in one of the morning 'khanas as I did get one of your runs on tape. It's 2.45Mb in size.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...