Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Guys,

Im looking at ordering new wheels soon.

Anyone have experience running 19x10.5 + 12 wheels?

Any rubbing front/rear?

Was also thinking about going 19x11 +12 at the rears. Anyone run this before?

On a R33 GTR??

you want the same all round for that.

10.5+12 will be maximum

ofcoarse you can run any brake size with 19s

I've seen brakes not clear 19's on a r34 gtr, he had to get specific 19's but mostly ran 20's. Dunno what brand of brakes they were but 8 pot fronts and 6 pot rears, set him back around $15k I believe.

I've seen brakes not clear 19's on a r34 gtr, he had to get specific 19's but mostly ran 20's. Dunno what brand of brakes they were but 8 pot fronts and 6 pot rears, set him back around $15k I believe.

woooooooahhh

thoughts on 18x9.5 +22 front 18x10.5 +30 rear?

been reading through pages and pages but haven't found anyone running 18x10.5 +30 on the rear. will +30 be a problem with the strut or inner guard?

i want to run as close to 0 camber as i can

Hey guys,

I have never been completely happy with how my 18x9.5 +22 rims sit on my car.

So I decided to call up the place who did the wheel alignment and get the specs for the camber that they put on it.

Below are the details

Front Left: -2.27deg

Front Right: -1.14 deg

Rear Left: -1.39deg

Rear Right: -3.69deg

Does this sound right? I always thought 3deg camber was something the fan boys did

I'm questioning if he actually gave me the correct info.

Looking at some whiteline camber arms to help correct this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...