Jump to content
SAU Community

Recommended Posts

Looking at getting wolf s1p will 18x10 + 35 fit rear? Otherwise this

Skyline model = r33 gtst

Wheel diameter = 18

Wheel width = 9

Wheel offset = +27

Tyre size = 235 40

Modifications to fit = ????

10+35 SHOULD fit rear, I had 10.5+30 and it fit no issues.

Other than that, the 9+27 would be near on perfect.

Looking for some ideas on what size tyre I should run on my new wheels? These are on a 33 gtst.

Current specs are: Front: 18x8.5+35 235/40 Rear: 18x9+35 265/35.

With my mildly rolled guards they fit easily 15-20mm inside the guards and I can fit my almost my whole hand in and around them in the guard and get pretty much no scrub at full lock or anything but I'm not sure if I kept the same tyre sizes it would clear everything easily and not scrub like all shit. My new wheels are 18x9+20 all round so a fair bit more agressive offset but nothing crazy. I don't want much stretch and would like the largest and most practical tyre sizes I can fit without more guard work. Any help is much appreciated! cheers.

18x9+20 with 245/40 all round :)

Rolled guards, front upper control arms to help tuck it in. Bit of scrubbing otherwise

post-109116-14188220710166_thumb.jpg

Edited by dontyellpl0x
  • Like 2
  • 2 weeks later...

My R33 GTR on Work emotion D9r ... got them back in October on the 12th, just been lazy and havent up loaded anything.

Work Emotion D9R 18x10.5 +15

Federal RSR Semi slicks 265/35/r18

Hnngg.

Edited by sleptema
  • Like 1

Hey guys I'm looking at buying a set of enkei RPF01's for my r32 gtst, I'm just wondering wether 18x9.5 +15 fronts and 18x10.5 +15 rears would fit

Not a chance without work. Well, they'll fit... drivability is probably not great...

My 18x9.5 RPF1's all round on the BNR32 barely fit as width goes.

I can't remember if the GTST fronts are same but you'll need to run 245's if you want to not rub the guard liner.

You'd have 1inch sticking out at the rears with 10.5's, not even camber alone with get that back..

Lol this guy ^

What look do you want and how much work ate you prepared to do?

If you run 225 and 245 you will easily make it with camber and a big guard roll.

If you are going for something that will still grip then expect to pull guards a fair amount

Guard liners won't be an issue as they will have to be removed anyway

Hey can you guys help me out I have a 33 gtst and I'm looking to go different wheels, just wondering if I can 18" 8.5 +30 on the front and 18" 9.5 +38 on the back? Or should I just go same width front and rear, if so should I go 8.5 or 9.5 all round???

Hey can you guys help me out I have a 33 gtst and I'm looking to go different wheels, just wondering if I can 18" 8.5 +30 on the front and 18" 9.5 +38 on the back? Or should I just go same width front and rear, if so should I go 8.5 or 9.5 all round???

That's exactly what my old wheels were and it fit fine. 9.5+38 265/35 on the rear and a 8.5+30 235/40 on the front.

post-109116-1419911417604_thumb.jpg

Edited by dontyellpl0x
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...