Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

They are due to run out next week and have supplies arriving the week after. My dad works at the refinery....If worst comes to worst you can still use the premium unleaded (shell or bp), just don't run on high boost and don't thrash the car.....Simple.

Ok, got an update today. Shell & BP are running low on premium also. But they expect that the bit that failed will be fixed and up and running again by Wednesday. I don't think it was the compressor but it started with a C. Lol. Sorry I don't know much about machines and that kind of thing.

I asked how long it would take till we had ultimate back at the bowser and he said 1 or 2 days after they get it running. So if all goes to plan, we will have ultimate on or before the weekend. If all does not go to plan, then they have the supplies which are already on the way. So it shouldn't be too much longer *fingers crossed* all goes to plan...

from abc.net.au

BP defends delay in going public over fuel shortage

As reserves of premium unleaded fuel dry up in Western Australia, petrol

producer BP has defended its decision to delay telling motorists about

the problem.

BP supplies premium unleaded to more than 600 retailers state-wide but

has been unable to produce the fuel since a mechanical fault occurred at

its Kwinana refinery.

The breakdown occurred two weeks ago but BP only went public yesterday.

Company spokesman Peter Metcalfe says service stations are already

starting to run out.

"There's around about a dozen BP sites have run out completely and I

think in all honesty that situation is likely to grow," he said.

Mr Metcalfe has defended the time it took to alert the motoring public.

He says the company was not sure at first whether it had an issue and,

once the scale of the problem was realised, it tried unsuccessfully to

source additional supplies from overseas.

Motorists who can are being urged to switch to regular unleaded until

supplies are restored - hopefully - by late this month.

The Motor Trade Association says the fuel shortage shows there is a need

to set up fuel reserves in Western Australia.

The executive director of the association, Peter Fitzpatrick, says the

Government should stockpile fuel to help deal with any future shortages.

"We are very exposed with one refinery where you can have it break down

or get some contamination, and I think that the Government, and I've

asked them to do it, to look at it before, should have a strategic

reserve set aside for just this sort of contingency," he said.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...