Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

if you get a good one it will be quicker stock for stock than a 33gts-t, also stock for stock they handle better IMHO.

harder to work on than skylines but not too bad, with a lot of similar stuff in them. just remember most of them are a lot older than say r33's (which people seem to compare them too) so the age is the cause of a lot of things going wrong since most of them are 89-93 models. interior is also an older design when compared to an r33.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721697
Share on other sites

Same as ^^^^

Mate with a 90 TT Manual

Did the 100k service on it.

Were that frustrated by the end of the 7 hour stint that we could have killed someone.

Wost car in the world to work on.

Repairs are very costly as every single part is hard to get to.

Turbos are an engine out job if you ever blew one or wanted bigger.

They are very heat happy and without sufficient cooling they over heat.

Main problem is the heat damagge that the components cop with every rtadiator fan and clutch peice i have seen on a 300 in need of replacing.

can boost to 13-14 psi by simply buying 2 $3 welding tips with a .9mm hole

The power output is crazy with very minimal mods.

Do buy a 5 speed though you wont regret trying to find one :)

With boost ,exhaust pod and safc II tune he has 338rwhp with 14 psi

Edited by Slide
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721738
Share on other sites

very hard to work on. Things that are basic on most cars are a pain in arse on zx's. it gets to the point where it seems like the engine has to come out to do anything. and i dont really like the look of em either :)

Edited by RRR32_GoDzIlLa
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721774
Share on other sites

After having a drive in a manual TT, I agree with the car's owner who said they make a great cruiser. Loads of power available, nice handling, but don't buy one and try and drive it like a WRX.

I love the cockpit. Almost as good as an R32. It was Nissan's attempt to produce a car marketable in America against Corvettes and the like.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721841
Share on other sites

cons

overheating issues

biggest myth, as long as it has been even half decently looked after.....

Oh.. and although people say it's heavy, it's no heavier than a line....

former owner.... cant wait to get my hands on another.

The cons are that it's very tight engine bay. very hard to get your hand in anywhere around the block.

also you don't want to trust just anyone with repairs/mods/servicing as most people cant even find the air filter, so it will cost abit to get anything done on it.... my recomendations are Unique auto sport in castle hill, they are Z specialists, so they know what they are doing... but it will cost abit.

great car.... i've got nothing but praise for it.... check out Aus300zx.com for info on what to look out for when purchasing one....

Edited by Archie@
Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1721843
Share on other sites

What is it with people's obsession with being "different", at the expense of logic and reason?

I'm not necessarily saying that a Z32 is a bad choice, but "spending extra every time" for no appreciable gain (aside from this insecure need to be "different") just strikes me as a waste of time and money.

If you truly wanted to be different, get your hands on an R34 coupe shell and do a CA18DET conversion out of a Nissan Exa. You don't get any more different than a FWD Skyline with a 4 pot, so you can brag to all and sundry about it.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722504
Share on other sites

I think that the Z32 is a nice car if you want a grand tourer. Its got plenty of poke, and its cabin is quite a nice place to spend time.

And yes, it does have a reputation for blowing things up so much that writing about all the ways in which they could fail would probably get you arrested under the new anti-terror laws.

And while yes, if its been well maintained it'll be OK but then that's true for any car. Even something as breakage-prone as a pre-Ford Jaguar will generally not shed bits if its been "maintained". The question is, if the average person owns one and treats it like a car, rather than with the loving tenderness akin to their own genitals, will it fail?

Not every Z32 was bought by people who took great care of the cars. You had a lot of mid-lifers who bought them as a status symbol rather than performance, then you had a lot of young people who had to stretch to afford it and couldn't afford to maintain it.

And, in those circumstances, the Z32 TT tends to be a lot less reliable than most. Such a cramped engine bay and all that heat adds up to mechanical and electrical failure. The cars are also getting on, and any work is a major effort.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722511
Share on other sites

Freshly imported z32 5spd tt's  for 10 k comlied and registered though.

If that isnt bang for your buck i dont know what is

If the car's your typical 10-15 year old thrashed out Jap import with an unknown service history, you'll certainly get a lot of bang.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722524
Share on other sites

When i was chosing a car, 300zx tt was on the list, and knowing diddley squat about cars and the such, one thing i could tell.

Pop the bonnet and look how cramped it is!

Jeeeeeze!

You can tell that if anything needs to be done, it'll be a job and a half.

On the other hand, i reckon they look fantastic! Was good to see it in Kill Bill too!

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1722818
Share on other sites

they dont overheat, its just that the heat in the engine bay takes its toll on other components.

Reminds me of that quote from Collateral:

Max: You killed him?

Vincent: No, I shot him. Bullets and the fall killed him.

Link to comment
https://www.sau.com.au/forums/topic/95156-300zx-twin-turbo/#findComment-1723218
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...