Jump to content
SAU Community

Gb: R33 Gts-t And Gtr And R34 Gtt Radiator Guides


Recommended Posts

The following people should keep an eye on their mail box in the next few days.....

2BNVS

GTS-T V-Spec

ZXFIRE

wolverine

Lordsnipe

Alpine Stars

bilbo117

Sydneykid

Trick

Cooper

I'm on a list!!!

Cakes and pies cakes and pies! :sorcerer:

  • Replies 520
  • Created
  • Last Reply

Top Posters In This Topic

Hey guys.

Thanks for the pics, they look even better on the car!

I should be able to pick up the anodised guides today, so will finish shipping them all this week.

BASS OUT

I received my guide yesterday and it looks good!

I'm not 100% sure about how it fits though. Has anybody fitted theres to their Series II?

You can see from the pics that the guide sits right up against the bonnet latch. It's not too bad, you can still open the bonnet but I thought it'd come down a bit lower.

You can also see that when the bonnet is shut that the airflow to the air filter snorkel would be more restricted than what it was from factory?

post-19364-1147737675.jpg

post-19364-1147737687.jpg

post-19364-1147737695.jpg

post-19364-1147737702.jpg

Farkin.

On the Series II I checked them on at the SAU BBQ after Christmas they were perfect.

Is your front bar standard? Is anything modified?

Cheers

Pete

PS Freeman,

I was going to be a smarty pants and say "When I get your delivery address" but I just realised that I now have your delivery address, so your guides will leave today or tomorrow with the Anodised ones.

The Anodised ones are on their way to me right now.

Pics forth Coming.

heya Bass Junky,

I'm at work atm so I can't measure it up, I'll do it at home.

My front bar is stock except for a lip which has been put on before I bought the car. I didn't think the grille was anything aftermarket?

Here's a piccy...

post-19364-1147740477.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...