Jump to content
SAU Community

Recommended Posts

Wet filter will screw up your AFM.

That's the first time I've heard that but I'm not the type to disregard someone elses view =) Personally I would have thought that if the filter was dripping wet then maybe it would have some effect on the afm. Perhaps a better name might be a slightly moist filter rather than a wet filter. Anyone else have views on wet filters? (not K & N specifically) as I'm curious =) Thouhg I'm not about to change mine anytime soon.

trust airinx isnt too bad, ive got a blitz sus stainless on mine now and its incredible. heaps good flow and looks awesome too.....id suggest getting one of those, but nothings wrong with apexi pods - im surprised mine hasnt got an apexi pod seeing how its got an apexi RX6 turb....the guy whacked a blitz on it, smart guy i rekn

wouldnt organising a sealed air box with a pick up that drew clean fresh air be more beneficial than this "name brand" is SIKER than that one.I can only speak for what i have seen but we only ever ran K&N on the Willall car and now i do after a certain Jap.foam filters cost me a set of Turbos on mine.

My car makes 255rwkw at the moment with the stock airbox and k&n flat panel air filter.

We tried taking the air filter out and running none - dynoing with the bonnet up and lild off the airbox it made absolutely no difference in power output.

Cheers

My car makes 255rwkw at the moment with the stock airbox and k&n flat panel air filter.

We tried taking the air filter out and running none - dynoing with the bonnet up and lild off the airbox it made absolutely no difference in power output.

Cheers

now set up a pod with cai and see what happens

My understanding is such that you should blow it out with compressed air at regular intervals. I can't imagine any performance car owner with half a brain not EVER servicing the device that filters the air going into the engine....Not trying to start a big debate just saying that most sensible owners are fairly adamant about regular services =)

Dezz the Apexi items are meant to last for ages and are claimed as zero to little maintenance. You gotta make the choice if you wanna do nothing, blow it out at regular intervals or use a non dry filter. I went with wet purely because it encourages a regular service routine =)

My understanding is such that you should blow it out with compressed air at regular intervals. I can't imagine any performance car owner with half a brain not EVER servicing the device that filters the air going into the engine....Not trying to start a big debate just saying that most sensible owners are fairly adamant about regular services =)

Dezz the Apexi items are meant to last for ages and are claimed as zero to little maintenance. You gotta make the choice if you wanna do nothing, blow it out at regular intervals or use a non dry filter. I went with wet purely because it encourages a regular service routine =)

So you put on a wet filter to make your life harder?

LoL. Perhaps we have a different approach to car maintenance. I'd personally rather know that the filter requires cleaning and do it and have a nice clean filter again, personal preference =) Then again, your question was essentially rhetorical anyway so I'll leave it at that.

Side note: Good to see a wide range of views too, be boring if everyone went the same route.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...