Jump to content
SAU Community

Recommended Posts

Cheers for the lesson. Didn't realise that 1.1mm and 1.2mm where very close in size..

The reason I asked is cause the chart listed early stated 1.25mm for street, 1mm for drag/circut.

I plan on doing all 3 of the above tasks and thought a 1.1mm was a good inbetween spot but wasn't sure if a 1.1mm restrictor would cause any issue's on the street.

I have a 1.1mm and a 1.2mm sitting in front of me.

Some of these things are calculated. You can't just feel like a number inbetween is good.

Depends how pedantic about it you want to get, you can sit down and work out your tolerances and intended oil viscousity and oil pump flow and pressures etc etc, then intended use for the car and then after all that just whack the 1.2mm in there lol

I have a nitto pump and use 10W40 with relatively tight tolerances and have two 1mm restrictors in the RB2630 and use the car for whatever is goin on :)

Is your larger sump suitably baffled and gated? Accusump is not a bandaid in my view but a valid solution - but it costs a bit and takes up room.

Ive got the Same problem with My 34.

Under Hard braking aswell. Pressure drops to about 20 psi with the rpm still around 4.5k

Only has a stock sump , but most of the aftermarket sumps only really allow for oil surge during cornering

What Brand of sump are you using

I use an ASR sump... Its only the street/race version not the full race (Not 100% sure what the difference is)...

Oil pressure is fine belting around corners and bouncing off ripple strips etc, its just under brakes...

Its dropping below 20psi and it regains as soon as throttle is applied.

The last track day at SMSP South did not have the issue but i assume that is due to the lower speed of the track which doesnt require braking as hard...

Depends how pedantic about it you want to get, you can sit down and work out your tolerances and intended oil viscousity and oil pump flow and pressures etc etc, then intended use for the car and then after all that just whack the 1.2mm in there lol

I have a nitto pump and use 10W40 with relatively tight tolerances and have two 1mm restrictors in the RB2630 and use the car for whatever is goin on :)

I noticed at SMSP South :ph34r:

Been looking to get a proper circuit sump for my rb2630 for awhile... I don't mind spending the money but I want to get the best one. One that fits with the white line sway bar that's already in the front of the car(and rear).

I would like to get asr but it's not good to read they don't fit and hit swaybars and/or need to be modified when they arrive. Then it's not good to read they don't actually prevent the oil pressure dropping under braking.

Does rips do one that works?

If it was for a gtr motor I would contact racepace and get them to modify the stock alloy sump as they do for the gtr's. Does anyone know if they will modify a tin sump to proper specs?

I've been tempted to run it with the stock sump but I don't really want to do that

Been looking to get a proper circuit sump for my rb2630 for awhile... I don't mind spending the money but I want to get the best one. One that fits with the white line sway bar that's already in the front of the car(and rear).

I would like to get asr but it's not good to read they don't fit and hit swaybars and/or need to be modified when they arrive. Then it's not good to read they don't actually prevent the oil pressure dropping under braking.

Does rips do one that works?

If it was for a gtr motor I would contact racepace and get them to modify the stock alloy sump as they do for the gtr's. Does anyone know if they will modify a tin sump to proper specs?

I've been tempted to run it with the stock sump but I don't really want to do that

Tbh, mine has rubbed on the swaybay and i was going to look at alternatives when the engine comes out next...

I was annoyed when i first went to Wakie and saw the problem. The car has now done 5 full track days and is still kicking which is a good thing.

Been looking to get a proper circuit sump for my rb2630 for awhile... I don't mind spending the money but I want to get the best one. One that fits with the white line sway bar that's already in the front of the car(and rear).

I would like to get asr but it's not good to read they don't fit and hit swaybars and/or need to be modified when they arrive. Then it's not good to read they don't actually prevent the oil pressure dropping under braking.

Does rips do one that works?

If it was for a gtr motor I would contact racepace and get them to modify the stock alloy sump as they do for the gtr's. Does anyone know if they will modify a tin sump to proper specs?

I've been tempted to run it with the stock sump but I don't really want to do that

The Accusump is a good fix but if the setup is designed right from the get go there shouldn't be anything to fix, I went through the data logging from SMSP last Monday and I have no drops of oil pressure at any point, fuel temp on the other hand got very out of control most likely the cause of it breaking down after a few laps :(

The Accusump is a good fix but if the setup is designed right from the get go there shouldn't be anything to fix, I went through the data logging from SMSP last Monday and I have no drops of oil pressure at any point, fuel temp on the other hand got very out of control most likely the cause of it breaking down after a few laps :(

Fuel temp should be sweet on mine as i have the cooler setup... Oil pressure, well ill monitor it and fix it if it causes me a hassle.

Haha, unfortunately that didn't work for me twice now :( so data log check everything as I go :)

Mat, what fuel cooler setup have you got cause I'm goons have to do one and maybe so will as he was having the same issue as me

All you really need is a transmission cooler or similar with pipe size through it approx the same diameter as your fuel return line. Best sort of location would probably be near the back of the car just before the tank return, and you might need to consider ducting some air to it from a scoop under the floor. I would do this rather than locating it at the front of the car for fear of opening a fuel leak during a front end collision.

You can buy dedicated fuel coolers, but I'd experiment with something nearly free first.

I just don't look at the gauges and hope for the best. It seems to have worked for the last 2 years.

Been trying that, so far so good :P

Haha, unfortunately that didn't work for me twice now :( so data log check everything as I go :)

Mat, what fuel cooler setup have you got cause I'm goons have to do one and maybe so will as he was having the same issue as me

Just a custom setup made by JEM... There are pics in my build thread somewhere :)

  • Like 1

Ok sweet, I'll have a run through and see if I can see it :)

I've been looking into tranny coolers but finding one to suit the -8 lines is proving difficult as they all seem to neck down to 3/8ths, otherwise yeah am planning on putting it at the back so it gets protected by the rear diffuser

Tbh, mine has rubbed on the swaybay and i was going to look at alternatives when the engine comes out next...

I was annoyed when i first went to Wakie and saw the problem. The car has now done 5 full track days and is still kicking which is a good thing.

Thanks for the reply, I'm still not sure which is the best racing sump to buy though. What proven alternatives are there to asr? Is it too much to ask for one that fits and works

Going off a few threads (eg. http://www.sau.com.au/forums/topic/266179-high-energy-sump/page-3) I've read before and will read again probably I think I'll contact asr and lewis engine and see if they can send me some pics etc. it's only for a basic rebuilt 2630 with -5 turbos running about 1 bar boost but I'd still like something that will work and keep the engine alive.

Edited by Gts30t
  • 1 month later...

Ok since I'm running a single turbo and have the original rear turbo drain fitting on the block, blocked off, I've noticed afew people run a hose from that rear turbo drain up to the cam cover fitting,

Would this act like a vent ? Is it worthwhile in helping the crankcase vent and help il drain quicker ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...