Jump to content
SAU Community

Recommended Posts

For some of the people in this post who didn't get what I was saying-

- it's not a fault. all buses do it of certain make(s) do it.

- i didn't say it was necessarily a bov used for turbos. it is air escaping so it's "blowing off" in some form or another. personally i think it's the door/brake pneumatics.

- it hurt my ear and I want to sue the government (not serious) so what would i do? why isn't this noise pollution? (does anyone know if it's just accepted or 'enshrined' in law somewhere?)

Thanks :(

... ps.

Can anyone tell me where to get one of these bus BOV's? and is there an adaptor to fit them to my laser turbo?

SIK WLEH BROTEC comes to the rescue.. PM me for a good price.

You sure thats an exhaust brake?

Not saying your wrong but I drive trucks and have not seen one set up like that before. I have only ever seen the butterfly flap in the exhaust pipe and the Jake brakes which hold the valves shut for the engine braking. How does that one work.

In relation to to BOV noise, as mentioned its the pneumatic release from the air brakes and in a bus situation from the airbag suspension as well. Sometimes when there stopped on a slope you see a bus rocking forward and backwards as the airbags try to level themselves.

I look at the engine setups on our trucks all the time and I have no friggin idea whats going on. One engine has an internal wastegate along with an external gate as well that seems to vent back to the inlet manifold?

And on the inlet piping they have multiple pressure actuators that I have not a clue what they do, when they open/close and what for.

couldnt they suppress it something? it shouldnt need to be that loud...

it real bad in a loading bay, the truck reverses in and the brakes squeels a little before it stops, then PPPPSSSSSSHHHHH!!!!! and you nugget your pants :/

Yep, that's an exhaust brake. A Jake brake uses oil pressure to the hydraulic lash adjusters which cracks the exhaust valve on the compression stroke preventing the compression ignition combustion (no spark plugs) from completing so it "brakes" the engine.

Don't be afraid big rig and bus noobs, the noises won't hurt you. :P

Its can also be height adjustment

Thats air driven aswell (esentially air bags i think).

SOme super new buses can change ride height depending on passenger load.

They too can be noisy. Not as loud as the compressor veniting though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you pay with a credit card? I'd be putting a charge back through then finding a new sparky to sort it out. 
    • If you mean the alarm immobiliser; theyre internal to the alarm itself which makes that difficult; I couldnt even see where he put it; its not in the same place as last time; but with all black wiring it might be very challenging to trace  I had someone turn the key for me as I know it only primes for a couple of seconds As my post above; I am getting no voltage to the pump at all; but I am testing continuity of the power line (SB) from the pump plug to the relay fine. As well as the negative from the pump plug to a 12V constant.    Yeah; he blammed the no start on a bad battery; said I needed to get a new battery and it'll start. Turns out the battery drained because the tail lights had been on for half the day during the install (the rubber cushion on the brake switch gave out while he was testing it as I have a picture of the car from that morning with the tail lights off..i've replaced that). The battery was turning over the engine just fine for a long time; but got low since lights were draining it so it was too low to test a start after he finished. I bought a new one on his advice...$250 wasted. My original battery charged up just fine and is healthy.    It was running perfectly fine when I messed up the old alarm (programmed out the remotes). He couldnt start it after removing the old alarm; my assumption is that when he unhooked it; he didnt bridge the circuit back when trying to start it. Its always been perfectly fine. The ECU swap and pump were 2 years ago. It's never missed a beat in that time. 
    • This is a big issue for me without the diff. I just have zero drive from the passenger side when drivers side has no traction. Bec's parents place has a crazy steep driveway with odd camber and I have never been able to get up. My bro-in-law's 130i with an (unknown brand) LSD gets up fine as does their dad's Hiace. My car stays at the bottom. We have other odd camber roads around here as we're elevated a bit and if it's raining I can get totally stuck around some hairpins. 
    • Yeah, I am super excited for this.
    • Was the car running before he touched the car?
×
×
  • Create New...