Jump to content
SAU Community

Recommended Posts

From my experience and Scotsman who spoke to racepace a while ago. He said ben said some pfc's do it and some don't. It seems to happen when the pfc jumps out of or into closed loop - using the o2 sensor. You can stop it by turning the o2 sensors off I have been told.

Didn't read the whole thread though. Am I close??

Mine were always off. Still did it. Tried the old extra ground to the ignitor trick, no good......

Carton to the person that gets rid of this damn hiccup for good!

Edited by GTRsean
  • Replies 212
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

i have the same problem but i have splitfire coils, hks ignition amplifier new plugs and earth lead and still does it, i am however going to put a new ignition sub harness hope this fixes it.

a little more information if it helps anyone with ideas, i run PFC 8.04a and suffer from the hesitation. a little while back i swapped it out with a mate running the exact same version, ran it for a period of maybe 3 - 4 weeks without a hitch. swapped back and the problem came back with it. so it was looking like it was only specific units, however recently his has started getting the problem after a long period of hassel free driving... as mine was second hand when i first received it and his only played up after a while, could it be somethin that comes with age? something breaking down?? has anyone had the problem with a new from the box PFC?

i'd be interested in the pin connector (blue thing) and the state of it

is your securely fastened and neat or is the wiring shabby and kinked etc?

it could be something as simple as the pins for the ign for each cylinder is a little weak/finicky

and when users remove the stock ecu and fit the PFC its enough movement to make it not contact properly

its a long shot , but would explain how your mate now has the issue you mentioned - only after removing ECU and plugged in a new one

so it could be the connector on the car side (blue plug) or the socket on the BNR32 PFC's

Yeah i got this prob too, does it once every couple of weeks...sucks to do it every 15 mins! farrrk

put in splitfires STILL DID IT

changed the ignitor STILL DID IT

changed the cas STILL DID IT

added earth wires STILL DID IT

I got over it...seems too hard.

Any other model car do it? Like 33 GTSt etc..

yes does it without hand controller, i try leave my controller unplugged so stupid passengers dont go "ohhh can i play the playstation" and pick it up and end up with god knows what. as for my wiring, you could say its a bit of a mess its an accomplishment in itself to unplug the thing.

Ive just removed my twin turbos and replaced with large single so its going for a tune next week, ill ask matt spri at PITS if he has any ideas that man knows PFC's like the back of his hand.

Edited by ow_damnit

Tried regrounding the ignitor pack and no sucess, has anyone tried to contact apexi in japan and ask for a fix. Maybe it maybe a companent in the ecu which is not soldered in, software????? This is very annoying

Anyone tried running datalogit with sucess maybe a solution if someone does.

Edited by cefiro

Mine is doing this too - such a pain. I think Paul you might be on to something with the pins - going to get in and push on each of the IGN wires hope it makes a different.

Some days it wont do it at all, other days it will do it every 15 minutes.

  • 4 weeks later...
  • 3 weeks later...

I had never had this problem with my BNR32. I have a completely new ignition system, all looms, earthing kit, HKS DLI twin power, Splitfires. But I had my engine rebuilt, and since getting it back, I get this damned hiccup/stumble at around 2500rpm at light throttle. It usually misfires once, but sometimes twice.

I question whether its an ignition problem because I have wideband logs. If it were an ignition misfire, the AFR would spike rich, and ignition cuts are smooth anyways. This hiccup is a slight jolt, and if you've ever hit a fuel cut limiter, you'll know just how bad a fuel-cut jolt can be!! Anyways, when it misfires, the AFR spikes LEAN. Meaning, the ECU is cutting an injector or two...implying a software bug.

But the thing is, it hadn't done it before. Only after getting rebuilt, and my earthing wires did get moved around to different locations. I'll try to put them back where I had them, see if that makes any difference.

Add me to the list!!!......

i have a 95 r33 gtr, with power fc, and have the occasional hiccup with the car at light loads, generally ~2500-3500rpm....

Im so used to it now it doesnt bother me (so long as it doesnt damage its all good)......i have it happen once every few days....

both my 32 GTRs have done it. one didn't do it for years, maybe 2 or 3 years with the PFC fitted. then out of the blue it started. not very often though, and it's not very bad, just a minor anoyance. the other GTR had big $ engine, turbos, cams, AFMS, the full monty and it did it too. the PFC in the first one I bought used (but 8.04a) the other one I bought brand new also 8.04a.

I must confess I've done bugger all to fix it. but the first car I mentioned is about to get new AFMs, new injectors and brand new engine, and new coil pack harness and new grounding kit so hopefully it disapears.

I had never had this problem with my BNR32. I have a completely new ignition system, all looms, earthing kit, HKS DLI twin power, Splitfires. But I had my engine rebuilt, and since getting it back, I get this damned hiccup/stumble at around 2500rpm at light throttle. It usually misfires once, but sometimes twice.

I question whether its an ignition problem because I have wideband logs. If it were an ignition misfire, the AFR would spike rich, and ignition cuts are smooth anyways. This hiccup is a slight jolt, and if you've ever hit a fuel cut limiter, you'll know just how bad a fuel-cut jolt can be!! Anyways, when it misfires, the AFR spikes LEAN. Meaning, the ECU is cutting an injector or two...implying a software bug.

But the thing is, it hadn't done it before. Only after getting rebuilt, and my earthing wires did get moved around to different locations. I'll try to put them back where I had them, see if that makes any difference.

Sounds like ignition problem. When tehre is a missfire, the AFR goes lean, as an O2 sensor measure oxygen, which there is plenty when there is no spark.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...