Jump to content
SAU Community

Recommended Posts

this takeros stag is hawt

Namnls2.png

well done sweden

my RS4S takeros stagea resides in victoria w00t w00t fresh from japan.

post-18938-0-67087400-1340722708_thumb.jpg

post-18938-0-44063900-1340722724_thumb.jpg

and its genuine, including the CF bonnet, could use some of those eyelids though.

Edited by OMY31T

Koya Endless 19x8.5 235/35 tyres +12 offset all round, you can have rims made to order from koya. suspension is HKS Performer all round - if you havent seen these before, they were made inbetween the hypermax I and hypermax II, i had never seen them until i got them with the stag from japan, and i will say, they are pefrect for the street, i have hks hypermx in my r33, and the hard rock solid, these are nice for the street and still handle really well, i think the wagon handles even better than my r33.

  • 2 weeks later...
  • 3 weeks later...

Yo!

Here's a few new pics now when the summer came to Sweden.

I also mapped the car with the new GT2530-turbos and the HKS 264/9.1 cams.

497whp at 1.4 bar, that's really impressing power at such a low pressure (still stock bottom).

Here's a movie, 50km/h to 220km/h: http://www.youtube.com/watch?v=OEAbxzyr8LQ

And here's a movie from the mapping (making ~400whp at 1.1 bar): http://www.youtube.com/watch?v=lVp8rNBlRgo

And here's the photos!

bild11.jpg

bild13.jpg

bild.jpg

IMG_1553.jpg

Yo!

Here's a few new pics now when the summer came to Sweden.

I also mapped the car with the new GT2530-turbos and the HKS 264/9.1 cams.

497whp at 1.4 bar, that's really impressing power at such a low pressure (still stock bottom).

Here's a movie, 50km/h to 220km/h:

http://www.youtube.com/watch?v=OEAbxzyr8LQ

And here's a movie from the mapping (making ~400whp at 1.1 bar):

http://www.youtube.com/watch?v=lVp8rNBlRgo

And here's the photos!

Wow that looks freaking sweet...

Eyelids would match the grill... is that Dolphin?

Good to see it back on the road!

Yeah its Dolphin...I need to check our their eyelids as the only ones I can find on YAJ looks a bit ghey.

Yeah need skirts and rear but fark its expensive getting it from RHDJ....I haven't seen nismo bodykits on YAJ for a while...

I think I got lucky when I scored this bar landed for $400...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...