Jump to content
SAU Community

Recommended Posts

Some of you may know that apart from owning two R32 GTRs and a 1991 Peugeot 205 GTI (as my daily driver) I also cruise around in a 1989 Bentley Eight. For the last couple of weeks I have been using the Bentley as my daily driver as the Pug needs work, one GTR is sold (awaiting $) and the other has a blown turbo.

Anyway last Wednesday night I was returning home from a business meeting at about 9-9:30 pm when I was T-boned by an old EB Falcon. The Falcon hit the front left panel and then spun around 90 degrees and smashed into the rear left panel. I was forced over 4 lanes of traffic (two with oncoming traffic), over the curb, across the footpath and partial through a wire fence on the other side of the road.

The facts are that I had NOT been drinking or taking any other substances, I was travelling between 60-62 kmph in a 60 zone, I was wearing my seatbelt and the other car hit me. What is in dispute (ie my word vs theirs) is who ran a red light. There were three witnesses but all put the wrong car on the wrong road heading in the wrong direction. Please do not make reference to fault as this is yet to be determined by the investigating officer and I do not want to impair any legal proceedings.

I spent the first night in hospital and the last 3 nights at my mates parents place as his mum is a nurse and nearly my entire family live overseas. If I can figure out how to post images I'll add some before and after photos.

PS - the Bentley was a 1989 model and had only travelled 51,360 km. What an inglorious death. An old Merc would have been more fitting.

post-19208-1168226223.jpg

post-19208-1168226265.jpg

post-19208-1168226296.jpg

post-19208-1168226336.jpg

post-19208-1168226356.jpg

Edited by writeoff
  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

It was a female driver with a male passenger that hit me. They were taken to the Royal Adelaide Hospital aswell and were worse off than me. I asked about them about 10 times but wasn't given any information. At the crash site I could hear the woman screaming in pain and a guy who stopped said there was blood all over her car.

After shots

post-19208-1168226634.jpg

post-19208-1168226659.jpg

post-19208-1168226680.jpg

post-19208-1168226718.jpg

post-19208-1168226774.jpg

post-19208-1168226795.jpg

post-19208-1168226819.jpg

post-19208-1168226853.jpg

post-19208-1168226923.jpg

post-19208-1168226966.jpg

For those in SA who know the roads - I was heading south down Marion Rd (the middle photo shows south bound traffic). The Falcon was heading west on Richmond Rd. They hit me and forced me across 4 lanes of traffic ie the outer lane heading south, the turn right lane & and the two north bound lanes on Marion Rd. From the last photo you can see that they ended up on the island in the middle of the road (you can see the marks on the road) and I ended up in the wire fence on the other side of the road. The first photo shows where I hit the curb and went into the fence stopping about 1 metre in front of that big tree.

Edited by writeoff

No, although Richmond Rd ends at the intersection as a main road (two lanes each way) and continues as a smaller road on the other side (one lane each way).

Condolences on the loss of an amazing car. Is there no way to salvage her with brand new parts via insurance?

Thanks. I doubt that it can be repaired as these cars are hand made by Europe's finest coachbuilders. I'm yet to hear the insurance company's decision as to write it off or repair it so I may be premature in saying that the car is dead but the chasiss is twisted fairly severely.

looks like a nice old car, when i was getting a wheel alignment last there was one up on the hoist before me and i was having a chat to the guy about it, aparently the body is lowered ontop of the chassis, not combined together so (i know its got nothing to do with you) but you can take the body off etc, they also run the same fuel injection system that my old audi 90 used to have, and i was amazed by the turbo setup on this old bently. it was pretty impressive, and always hurts to see someones pride and joy mangled!

all the best

bummer. well not to matter who's fault it was. the main thing is everyone is ok and that you have your insurance. They will take care of you, and let everyone else figure out who's at fault.

sad to see a nice car like that crashed

i used to work for benlty as an apprentice in melbourne. and i did see some bad crahse with prestige cars as we also had a panel shop. (f430 ferrie spun of road at 140km/h and hit a pole )

but sad to say i believe there would be at minum $40000 worth or repairs to that car if not more.

hope all goes well tho and good luck

wow... that sux. I sure the otherguy is shitting himself thinking " how much does it cost to fix or replace a bently?!"

agreed - but i dont think they are the only ones shitting themselves..........

Thanks. I doubt that it can be repaired as these cars are hand made by Europe's finest coachbuilders. I'm yet to hear the insurance company's decision as to write it off or repair it so I may be premature in saying that the car is dead but the chasiss is twisted fairly severely.

.....and this is the reason - insurance are probably shitting themselves as well....

bad luck man...she was a beautiful ride.... :kiss:

the car held up pretty well considering a tbone. good old brittish engineering. hate to see what the falcon looks like. shame, at least your alright.

I didn't see the Falcon but was told it was a hell of a lot worse than my Bentley. They hit a 2200kg British tank headon and knock it across four lanes of traffic. I hate to think of what state I'd be in if I was driving my 900kg Peugeot 205 GTI.

Thanks to everyone for your thoughts and well wishes.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...