Jump to content
SAU Community

Recommended Posts

just made this mod to my car & it has made a difference to the cooling of the a/c, i dont know how many degrees it has dropped BUT i can most certainly feel the drop in temp :P thanks cubes :D

  • 7 months later...

tried this mod and it works like a charm but i decided to change the pressure switch ($73 and plus gas$50) and make the fan auto. but anyhow thanks very much for sharing it with us and 10 out of 10 for instructions.

  • 4 weeks later...

took me a while, but I finally got around to it ;)

just to confirm for others. on R33 its the pin on the far left (driver's side) on both relays. Same as cube's original instructions for R32.

I found this pic on the internet.

diode1.jpg

It does look identical so I'd say yes.. Its the 1N4004

i havent put a diode in yet. the one above is rated at 400V 1A. Is 1A ok for this application?

Edited by Munkyb0y
  • 4 weeks later...

ok, i've noticed something strange. r33.

if i turn my ignition on, but dont start the motor, then turn ignition off, my ignition lights stay lit.

after some poking around, i discovered if i disconnect this mod, and replace the relays as per standard, the problem goes away.

anyone else have this?

  • 1 month later...

Did this Mod on my R33 yesterday but will see how it goes this week.

it looked a little bit harder than the R32 pictures but once you move washer bottle and undo the power cables (unplug battery in boot first) it help get under the relay.

I spliced into wire 2 on each relay (under the relay it will list what pin 2 is and then where that pin plugs into I spliced into that wire which was the left one for both)

  • 11 months later...
  • 1 year later...

I don't think this can be done on a R34. The 'blower' fuse is located inside the cabin. Can someone with a R34 comment on this?

I did it to my r34 gtt but I used the relay to kick in my electric rad fan relay ( aftermarket fan which ive done to many r32s aswell)

QUESTION: Will the fan get "burnt out" slowly wear out if the fans are turned on at speed ( 80-200kms) or would the wind speed going 200k on a "track" be nowhere close to the electric fan speed??? note extra fan is mount horribly through the rad core

cheers

  • 8 months later...
  • 10 months later...

Would also like to know if this works with R34 GTR, as my aircon is slowly begins to get warm when stopped at a set of lights on an extremely hot day, and cools down again when i'm driving, and my water temps seem to go up when i'm idling at lights but slowly comes down when i'm moving.

  • 2 years later...

I know this is a bit old but I have found out a much simpler way to have the Rad fan kick on then messing with the relay box and installing a diode.

 

very simple, 

all you need to do is jump the over heat switch.

35353195444_76b7612b49_b.jpg

(This is a test jumper, I have an old temp switch I'll chop and solder as a jumper)

Fan will only kick on when you turn on the A/C.

this fan will only operate with the A/C system engaged.

With the A/C off it will not turn on if the engine runs hot, if it did the fan would always be on when the jumper is installed.

Best part is you can revert back within seconds

Edited by Nissan_Junky
  • Like 1
  • 2 months later...

Whats up guys. So I have been trying to figure some stuff out before I do this mod. I know this thread is very old but maybe the GTR gods can help me out. From my understanding the aux fan comes when temps go over 90c. Does the fan come on only when the aircon is on or does it come on any time the engine goes over 90c regardless. I ask because my fan comes on without a problem when the aircon is on and it goes over 90c but it does not come on with the aircon is off. The service manual under the coolant section says to jump the plug just like the user before me did but it only comes on instantly if the aircon is on. 

I think I am having issue with the aux fan coming on independent from the aircon. I may be wrong so please correct me if thats not how it work. 

I have all the hardware to do the mod. 

  • 2 years later...
  • 2 years later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...