Jump to content
SAU Community

Recommended Posts

Also for aftermarket TB's and fuel rails you can try Buzz Engines in Brisbane. They have done some nice work. http://www.buzzengines.com/

I need to get a decent fuel rail for the 26/30 as I'm running Delphi 680cc injectors and the O ring setup is not optimal with the GTR rail.

by not optimal u mean no fooking way it fits? :thumbsup:

theres also bmi, im usnig one of their billet throttle bodies

thats also something id like to make on our cnc's when they are up and running properly some billet fuel rails....im in love with these machines and they arent even setup fully and running...however next week they tell me!

do u have access to 6061 t6? my billet girdles will be ready to produce next week...wink wink

repco only sort them by size not car.

called up a mate from nissan parts, said i need about 7 of one size (think its 22mm) and 12 of another im not sure of.

i bought

6 x 22mm

11 x 30mm

buy a couple extra as i believe i had a couple i didnt replace.

hey just wondering how you guys that have a single turbo on your 26 heads ran the coolant lines for the turbo, im doing a single turbo 26/30 and wanted a bit o info on if other people set up the coolant lines like that of a 25 or 20, ie just running the one from the back to the turbo and the return in the normal place, taking out the part that comes around the front and back intot he coolant inlet for the engine?

oh and before anyone just says search for it, I have and the results were pretty inconclusive

Edited by s13_Skyline_inside

hey guys have been reading this thread with a lot of interest, but have come to a bit of a cross-road

i have an s13 running an rb20det spinning a t04e, so i have nothing really down low, but it pulls very hard on boost (~4,500rpm), so i ideally want more torque and a more gradual power curve. the t04e is good for about 600hp so i would like to keep this turbo. other mods i have are oil cooler, front mount, link g3 ecu, bigger radiator.

i want to set up the car for drifting & racing purposes, and i came to decision between an rb25det or an rb30det. so for traction purposes i guess a rough power goal would be between 300-320rwkw

having read a fair bit of this thread, i would love to build an rb30det and whack it in my silvia, however if it was set up for drifting/racing, would this engine be too heavy for the front of the car? i initially also thought it wouldnt fit into an s13 however ive been told by a few places that one can use a cefiro cross member to sit it down low enough.

i read somewhere in the early pages of the thread that it would cost roughly the same to set up an rb25det as a well as a sort of standard rb30det.

my other issue is that if i started building an rb30det from the ground up, i would just get carried away with it, forgies pistons instead of stock, custom rods instead of stock, rb26dett head instead of rb25e etc and just be pushing for power i wouldnt need as opposed to just buying an rb25det halfcut, bolting my turbo and manifold on with some larger injectors.

after reading most of the thread, im inclined to think that an rb25det would be all i would need, but i thought id get some second opinions on whether a basic rb30det build (stock rods etc) would be more suitable due to the increased torque that it would make.

any help would be great

Edited by 454KEN

Just interesting in seeing whether anyone has used the cam belt from a 1.7 Mazda Diesel engine which apparently fits and RIPS in NZ is using. The shop that sells his parts sold me one, and im just wanting to know whether it fits like the rest.

What sort of hosing should i run as my oil/water feeds and what fittings am i likely to need also.

Im going to be running a wasted spark setup on my car with evo coils, so ill keep everyone posted with the results

Just interesting in seeing whether anyone has used the cam belt from a 1.7 Mazda Diesel engine which apparently fits and RIPS in NZ is using. The shop that sells his parts sold me one, and im just wanting to know whether it fits like the rest.

What sort of hosing should i run as my oil/water feeds and what fittings am i likely to need also.

Im going to be running a wasted spark setup on my car with evo coils, so ill keep everyone posted with the results

hi sir racer//ref cambelt..yep it fits. i have a gates belt thats a mazda 1.7d on my rb26/30 right now..no probs..

cant help on the other issues sorry,bernie

hi sir racer//ref cambelt..yep it fits. i have a gates belt thats a mazda 1.7d on my rb26/30 right now..no probs..

cant help on the other issues sorry,bernie

Hey Bernie,

Cheers for the reply. Is the tensioner tapped in the same place as all teh pictures?

Thanks

Hey Bernie,

Cheers for the reply. Is the tensioner tapped in the same place as all teh pictures?

Thanks

hi mate. i moved mine to just under the head. on the smooth part above the water pump. also used two tensioners, sounds sweet no whining noise like you get from the greddy belts sometimes..easy enough to do..

post-13735-1196369733_thumb.jpg

Edited by rockabilly

s13_skyline_inside: Normally out of the back of the waterpump you can T a line off there to direct it to the waterfeed for the turbo. Either that or drill a hole and weld a fitting on the outlet of the inlet manifold were the water goes to the radiator and direct it from there.

Doesnt std rb26 have one feed that splits into two. one for each turbo, but from the block somewhere?

yeh with the 26 there is a coolant line that runs around from the back around the exaust side and back to the front of the engine that both the turbo's feed of, I've seen some conversions where they havnt connected back to the front of the engine and was wondering if they did somthing else or just ran the feed from the rear outlet to the turbo and then return back to the block. the reason i thought that standard they connect back to the front of the engine was so that both turbo's got the same amount of coolant, kind of like a balance.

there are some pics of what i mean in this tread http://www.skylinesaustralia.com/forums/Rb...nt-t169610.html but the thread didnt really get many reply's about whether you can get rid of the front part of the line or not.

Edited by s13_Skyline_inside
hi mate. i moved mine to just under the head. on the smooth part above the water pump. also used two tensioners, sounds sweet no whining noise like you get from the greddy belts sometimes..easy enough to do..

Thanks mate, are there any specific measurements i should be telling my engine builders about where to mount it.

Any reason you also didnt go with tapping it as per everyone else? Your way does look pretty well done, im just a bit worried its going to get mucked up once i drop the engine off.

Cheers

I wouldn't be too concerned with specific measurements. All you need to know is 2 x tensioners... 1 positioned above the water pump on the inlet side and the other down in the tensioner location on the exhaust side.

Then dummy it up; grab the cam belt, came belt covers and position it so that it clears the cam belts. Failure to do so will result in the belt rubbing on the cam belt cover(s); which is what happened to some one I know. :)

Dummy it up; you can't go wrong. :)

I've attached the rb30 guide to this threads first page/post that contains a pic and measurements of the upper tensioner location courtesy of that Cobra dude. :huh:

http://www.skylinesaustralia.com/forums/in...t&id=132205

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...