Jump to content
SAU Community

Recommended Posts

It's not 75%

It's a set RPM determined by the EPA - which is more than that.

Either way, you need to be 89dB @ 4900rpm - that includes on back off/rundown. Which is usually what trips the meter.

Unless you have a stock exhaust, you'll fail.

My memory is hazy on this, but I thought it was around 60% of peak RPM (based on the factory limit) at 500mm at around 45 degree off axis with minimal reflective surfaces during the measurement (the meter must be away from reflective surfaces.)

Can't remember where I had this information though, so not 100% sure it's right...

EDIT: actually I thought it was 50% of max rpm...

Gotta find the EPA doc...

Edited by wht510

Well.. If he said you'll get it in the mail - guess what? You'll get it in the mail :merli:

You really need to have a read of this thread. It'll give you a fair idea of what you need to change.

You'll only need to change the things that can be picked up. ECU is obvious, you already know that. So what else does the ECU control? Injectors, AFMs etc. Only stock items can run on a stock ECU etc.

It's not 75%

It's a set RPM determined by the EPA - which is more than that.

Either way, you need to be 89dB @ 4900rpm - that includes on back off/rundown. Which is usually what trips the meter.

Unless you have a stock exhaust, you'll fail.

Unless you own a gtr which when it rolled out of the factory in japan was over the 90db limit for Australia ... go figure that one out.

A while ago i read there was specific areas that are exempt from height rules, from what i read it was a meter either side of the axles, downloaded the mod guide from vic roads to check and there is nothing in there any more, it is a new one too, october 2011 is the date on it now.

Last time i looked at it exhaust manifolds were free as long as all the original fittings were retro fitted, now you need to have documents from the manufacturer to say that the manifold you are using is suitable for that car/engine, im glad my chinese stainless manifold cracked and i went back to standard.

seems things are getting worse

Edited by W0rp3D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...