Jump to content
SAU Community

Recommended Posts

Hey guys,

My brother also owns an R32 gtst & when his engine is cold (left overnight) it hesitates on acceleration. If you keep the same peddle pressure it will hold back for a second then eratically rev harder as normal. Is this a normal thing? or maybe an issue? Having said that it operates fine once the car is at normal operating temp.

Thanks guys

Link to comment
https://www.sau.com.au/forums/topic/158452-r32-gtst-hesitates-when-cold/
Share on other sites

http://www.skylinesaustralia.com/forums/in...hesitating+cold

the problem is in the ECU.

it is nissans way of warming up the engine with minimal stress on the engine. it goes into rich and retarded mapping up until something like 3300rpm or until you put your foot down a bit more.

do it next time you drive it cold, keep your foot at the same level and get to around 3300 and you will notice a sudden rush as the fuel and ignition maps have gone back to normal.

it is completely normal

That doesn't sound right. The manual advises to drive easily when cold, till temps are normal, so why would they make the engine run shit at low rpm, doesn't make sense. :rofl:

When warming up all tunes run rich with retarded timing, but apart from a lack of power, this should not effect drivability.

That doesn't sound right. The manual advises to drive easily when cold, till temps are normal, so why would they make the engine run shit at low rpm, doesn't make sense. :)

When warming up all tunes run rich with retarded timing, but apart from a lack of power, this should not effect drivability.

The above is just a quote from the link i provided.

I am not sure whether this is normal or not, although most r32's seem to have this problem. Would like to know the answer to this problem :D

its a common issue

i personally think its got something to do with the oxygen sensor needing to be warm/hot to operate

it seems like when its off boost it has no power at all, but when it comes into any boost at all it jumps into life like it normally would

neither do i.

check your fuel lines nisskid and make sure they arnt perished through and leaking

yeh i figured it would probably be a leak in the line, weird thing is, it only smells when its cold and running, so unless for some reason the leaks would close up when its warm, doesnt really make sense.

do u 2 have straight through exhuasts, cats?

Only have catback exhaust.

Uploaded a video of my daily cold start. Anyone have similar?

As you can see/hear, the key is turned for a while, then it jumps to life and falls back to zero. a blip on the throttle brings it back to life and idles normally...

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...