Jump to content
SAU Community

Recommended Posts

hi, first time i'll be changing the oil in the new car (32gtr) and just wondering what these things like best? specially considering it's starting to get pretty cold here in canberra. also, are there any pointers about changing oil on these things or will it be as straight forward as my falcon? cheers guys.

ps, did search this but was surprised not to find anything.

Link to comment
https://www.sau.com.au/forums/topic/161928-best-oil-for-rb26/
Share on other sites

personally I wouldn't use anything other than Motul Chrono 300V 10W40.

for some reason, my motor does not like it

the car had a ticking noise at the top of the engine on cold start when i used to use 300V 10W40.

then did a bit of reading, found out that full synthetic oil can drain from the head...thats why i switched back to 4100.

but my car is only a road car, with a very light tune on it.

cheers guys. advantages of the 10-60w? is it just better in the heat?

In theory yes, heat meaning full race conditions not just a 40degree day, but do you need to spend that much if you are not racing.

Most people agree you need a fully sensethic oil. The nissan manual refers to 15-35w oil. Oils have improved since the manual was made. The lower the first number "generally" means the quicker it lubricates the engine at start up (where most engine damage occurs in a daily driver). Lubrication = protection. Canberra gets real cold in winter, starting a car in sub 0 weather benefits from a lighter oil. For more details and debate on oils see the what oil should I use thread, lots of good reading.

5 litres $50 for my oil.

X 2 i got a r32 gtr, shredder667 u can get it from Autobarn in fyshwick if u get stuck give me a PM i live in Queanbeyan

X 3

Did all the oils for mine a couple of weeks ago...

motul 300v 10w40 for the engine

red line lighweight shockproof all round for gearbox/front and rear diffs

not enough redline High temp ATF for the transfer case so ended up getting some castrols in there at the moment.

bit costly but drives smoother than ever :)

jeff

I've lost two engines using motul 300v doing track days, after the last one i switched two Nulon 15w50 full syn and a dozen track days later still going fine ( over a period of five years )

which 300V and what else changed in that period of 5 years?

10w 40 and two engines, oilcooler on second, unless there's somthing inside this one i don't know about but it should be stock and been in place for 3 years.

The factory workshop manual recommends 7.5w 30 sg grade ( but thats for japans weather ), 4.2 liters without filter change and 4.6 with.

Edited by XKLABA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...