Jump to content
SAU Community

Recommended Posts

I've seen how the Fatz and the Sil go at it.

And might i say they do a good job :P

Although the do carry a fair bit of dispersion into the battle. Its a tough ask for little fellas to keep up with that, but it didnt stop me trying lol

  • Replies 256
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yeah, I highly doubt steve was even born in NSW. most likely he was born in the south then smuggled across the border as an infant. or he may have been born in nsw, but not originally as a man.

you need to look to pillars of the comunity such as my good self and messers T brisby, Fatz and silhouette to see how fine gentlemen from nsw behave... no fangipani stickers, no gay metro mohawks, no died blonde highlights, no gucci sunglasses, no turned up collars, just good honest little battlers in town to drink all your beers, reset your records and root all your women (or men in fatz's case).

Well I'm from a bit further North but think I can fit that discription for the most part. NSW is home now.

Im in if you have shots of tequila!!!! :)

Ahhhhh God Bless Youtube

I was browsing some deca vids to show some of the WRX guys and I came across this,

and I didn't even know that was released :banana:

VIC FTW :banana:

Ahhhhh God Bless Youtube

I was browsing some deca vids to show some of the WRX guys and I came across this,

and I didn't even know that was released :thumbsup:

VIC FTW :P

That is a poor excuse of a man drinking....

He wont be letting the side down again lol...He has been in training :thumbsup:

*runs in*

hello mexicans!!

NSW ftw :P

*runs out*

*Runs in*

Hello Mexicans :)

NSW FTW!

*Throws eggs and runs out*

for the win "this"

can i spray ftw on someone's forehead

ftw and +1 are the new 'most annoying' terms on the internet.

Aww see now thats weird cause NSW is the whinging state dont tell me its spreading :P

yeah for the next half hour the next person to post FTW or ftw or For the win in this thread get's a warning level increase of my choice. so the question is, do you feel lucky??? punk.

yeah for the next half hour the next person to post FTW or ftw or For the win in this thread get's a warning level increase of my choice. so the question is, do you feel lucky??? punk.

WTF!! :(

yeah for the next half hour the next person to post FTW or ftw or For the win in this thread get's a warning level increase of my choice. so the question is, do you feel lucky??? punk.

Hahaha - i really wanna test my luck..........

but im scared :(

WTF!! :(

lol, man that was close, it's like the forbidded phrase, only backwards... and I wonder if quoting me saying it, counts as you saying it... hmmmm. lol

lol, man that was close, it's like the forbidded phrase, only backwards... and I wonder if quoting me saying it, counts as you saying it... hmmmm. lol

Smarter than the average bear I see, even after some beers :laughing-smiley-014:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...