Jump to content
SAU Community

Recommended Posts

I'm just about to do my first service on my R32 GTST since it arrived from japan.

The only engine mods it has is a full apexi exhaust.

It still has the factory airbox with a nonbrand name filter inside.

As an apexi filter to go within the factory box is around $80,

i thought i may as well buy an Apexi Pod filter that bolts directly onto the AFM for an extra twenty bucks.

The car has factory computer i dont think its had any tuning done.

It runs superb, so I didnt want to f**k anything up by adding the pod filter.

I'm just asking for peoples thoughts comments or suggestions.

Wether Its better i stick to the factory air box, or chuck this pod filter on?

And if any tuning needs to be done once the pod filter is on there?

Cheers

exhaust + filter are very minor mods, I think a remap would be an expensive way to gain a couple of kw.

box the pod if you want good performance, otherwise you'll suck in hot air. otherwise stick to the airbox.

the stock ecu can't be tuned without remapping it. if you take it to any random workshop with a dyno and ask them to tune it, there is about a 90% chance all they will do is a power run, and just have a look at the afr's. they probably won't even pop the bonnet.

Hmmm, my R32 GTSt was stock when I got it, I added a dump pipe back 3" exhaust and it went really well. I added a K&N pod with heat shied and it started hesitating when the car came on boost, like I was hitting a fuel/boost cut or something? I've since changed it back to the stok airbox and reset the ECU and it goes better than with the pod.

any tips when making an airbox to fit around the apexi pod?

Materials , dimensions, or anything to take note of?

Cheers

This is what i made up in 1 afternoon

post-28112-1181447982_thumb.jpg

post-28112-1181448136_thumb.jpg

post-28112-1181448157_thumb.jpg

Bellmouth attached to a 3" 90 degree bend

post-28112-1181448169_thumb.jpg

post-28112-1181448037_thumb.jpg

Half round heat sheild and bracket from super cheap

post-28112-1181448196_thumb.jpg

post-28112-1181448350_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...