Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

too right it would be, :-) i take some if you do make them. searched for ages for something like it. would not ba as simple as those i think... well on a R32 anyway and being able to split them rather then removing the drive shaft

post-28646-1181755552_thumb.jpg

post-28646-1181755732_thumb.jpg

Edited by tacker
Link to comment
https://www.sau.com.au/forums/topic/172697-brake-duct/#findComment-3177733
Share on other sites

it seems like it only cools the very centre of the disc... wouldn't it be better to have a duct cool the outer edge of the disc where the pads make contact or even ducting cool air into the the cooling vanes in the centre of the rotor? I reckon make somthing like a caliper that goes over both sides and the top of the rotor then duct cool air from the front bar into that... just my thoughts.

Link to comment
https://www.sau.com.au/forums/topic/172697-brake-duct/#findComment-3181781
Share on other sites

they do spray water onto the brakes of a DTM car but only when they are coming into pitlane as stopping with red hot brakes causes fade when they return to the track or so the article i found said. Also those truck they race pump water onto the brakes all the time.

I have also found some 3" 12 volt fans that are used in nascar to cool brakes down. They are place in the brake ducting and will move 145CFM i think that would help.

Edited by tacker
Link to comment
https://www.sau.com.au/forums/topic/172697-brake-duct/#findComment-3183429
Share on other sites

used to run water cooling in f1 as well as a way to beat minimum weights....they'd get weighed with 30kg of water on board then dump it on the brakes nice and early, then run around 30kg lighter :thumbsup: I still think there is a god chance of cracking them though

Link to comment
https://www.sau.com.au/forums/topic/172697-brake-duct/#findComment-3183478
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...