Jump to content
SAU Community

Recommended Posts

^^^ dnt stress to much about the latency, your tuner can do it 90% of the cars (even tuned) that come to my workshop have not even had this set..... i always set it but at the end of the day it wont effect the car bugger all if you just want to drive it down to the tuner.

the important one is the injector correction.

  • 2 months later...

hmm... coz i swap the little rubber o rins from my stock ones and put them on my new ones... put a tad of vasoline on them so they slipped in...

dang are they stufed now if there locked??

wll i found that the car was WAY flooded........ like un believable...

not before i got startin it.. the 66% and .18 will be fine??

or shall i got 80% as some ppl i know run 80% and .00

cheers all..

  • 4 months later...

i have a set of deatschwerks 650cc side feed (red) rb25det injectors and im not sure how to set the lag/latency. the information i have is:

16v - 1.072

14v - 1.192

12v - 1.420

10v - 1.8

8v - 2.62

6v - 5.88

now how do i change that infomation into a ms reading that i can subtract the stock injector lag from to enter into my power fc??

i think i have a more complete voltage list like that in my email (cant check it right now though, at work) that goes from like 4v to 17v for ever 1v if that would help anyone help me, i can post later

Edited by ANVIL

I also have hi flowed red top injectors for RB25, mine are 680. i think red tops come out of some 300zx's and KA24 or whatever the 2.4l nissan donk comes in bluebirds and US-spec 240sx's

i know the correction will be 54% but unsure of the Latencies.

i'm going buy what Uras (trent) said and hope the tuner will deal with it...

  • 5 months later...
just got an email from Deatschwerks which gave me this info for redtop side feeds the time would be .64ms

so:

.64 - .52 = +.11

i will post all the voltages too when i get home if i remember

ANVIL the voltages were posted for the DW red 650cc's above. I know it has been a while, but how did your RB run with these lag settings? And did you also change the latency settings "Inj Lag (ms) vs. BatV" to match the DW provided voltages??

  • 5 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
    • Yes they do. For some maybe. But for those used the most by abusers, ie Skylines, the numbers are known. The stock eyebrow height for R32/3 Skylines is about 365/375mm or thereabouts. The minimum such heights are recorded in adjacent columns in the database.
    • Hmmm, interesting. Makes me wonder whether there is bias as well. It's the cheapest fuel, so it is used for all kinds of ill-maintained shitboxes which are bound to have issues regardless. Nicer cars tend to require higher octane rated fuel and can't use it anyway. FWIW, the official NSW E10 facts page is decent. 
×
×
  • Create New...