Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

On freeway kms, with the cruise control on, that figure is achievable. I often get to those numbers when I have to get to the country for work. But once I hit the city again, they quickly decrease.

^^^ nah mine says that when I drive it a little bit on the highway after filling up .... then calms right down back to reality ....

I get between 5.9km/l and 7.4km/l in my coupe - and ran 10km/l on a highway trip .... fyi when it is only 5.9km/l I have done LOTS of sitting around idling with the a/c on full bore in 39 degree heat (like today) while I am working writing up reports on the go. Forecast is for 39 tomorrow and 40 Sunday cooling down to 28 Monday but back up to 40 next weekend - yikes! Gotta love Adelaide weather! (and I do).

But have you got cruise control? It really makes a difference. Especially if you cruise on just 100k/h. If you cruise on 110k/h the economy is not as great.

But if you don't have or don't use cruise control, then you probably won't get those numbers.

Yeah I have cruise control. But in SA the country speed limit is 110km/h and we have 10% tolerance here, so I sit on around 118km/h on the freeway. Hence 10km/l is absolute max.

Yeah that'll be right then.

We used to have the 10% tolerance here in VIC too and it was great, but now it's only 3kms over tolerance.

A friend got fined for doing 83km/h on an 80km/h zone. The width of the needle is practically worth 3km/h.

  • 7 months later...

Sorry to bring back up an old thread but I just got my V35 coupe 6mt a month ago so this is what I got.

Full tank at 76 litres I get 640 km which include 250km of country road, 150km of twisty hill run with a bit of squirt every here and there, and the rest strictly urban rush hour traffic. Not bad for a car like the V! I would say it's even on par with my 15 year old 4 banger Accord. Only difference is the V uses PULP.

Iv done 12km/l on the last two 350km return trips in my 350gt-8 (highway) The lowest i have had on highway is 10km/l and that was sitting at around 120km/h most of the way with some heavy foot in the twisty bits. Obviously im pretty happy with the gt-8.

Im actually scared to change out the dirty looking filter incase it ruins my economy. :rofl2:

Edited by austingtir
  • 1 month later...

I picked my 03 6MT Coupe up from sydney and drove it back from 8.30pm on sat and filled up near caringbah or tempe (forget where exactly), went to luna park to take photos and then went back to gold coast, got to ballina with fuel needle on the second line. Filled up the tank and it put 57.87L in it. so 22L left in tank (so 650km) 11km per L so another 250km left.. dunno if thats right but easy 800km. I reckon the whole 10 hr trip we saw 50 cars... was cold as too, around 3-5deg the whole way. Amazing. :D

Edit: is a coupe QV35-DE

Edited by R6n350GT
The graph on the next page is also very usefull-it shows you the average consumption by day/tank/last trip (im not sure yet)

The graph you are refering to would be the history, on the green leaf page there is two buttons, the one that is highlighted at the bottom when you go to that page will take you to the history page, the other button, when you push up on the joystick, is the reset button for the green leaf page.

So if you reset every time you fill up, you can collect consumption records per tank, not just an average over a couple of tanks if you choose not to reset.

Edited by pv35gt8
  • 1 year later...

i drive from sydney to brisbane on one 1 tank of fuel inmy sedan. and that was a 7 hour trip in my 350gt sedan also with a few luggage bags in the boot.

937 ks to the tank, shell v 98

Edited by black 350

i drive from sydney to brisbane on one 1 tank of fuel inmy sedan. and that was a 7 hour trip in my 350gt sedan also with a few luggage bags in the boot.

937 ks to the tank, shell v 98

7hrs from Syd to Brisbane?? how fast were you driving?? :worship:

I had similar mileage few years back when I first got my 350GT sedan...drove from Bris to Newcastle on one tank...approx 800kms.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...