Jump to content
SAU Community

Recommended Posts

I've done a search but can't find my answer...

- Is anyone running 17x9 all round? specifically on an R34 GTT

- Will 9" fit the front? seems most people go for 8"

- Can I go for the same width AND offset for front and rear? I was thinking 17x9 with offset in the range of +30 to +35.

specifically for a 34 GTT and only 17"

cheers

The offsets seem a bit too low.

if it's for a GTT

17x9 +20 is definitely not too low offset, IMO i wouldn't touch anything with a higher offset than that. Hell, i'm going to be running 17x9 +0 and 18x10 +12 on an S13 soon, will look tough as!

Hi guys just need some help while on this topic.

Ill looking at buying 18inch wheels with 18x8.5+43 Rears 235x40 & 18x8+41 Fronts 225x40.

Will these offset fit my R34 gtt?

Would it clear the brakes?

Thanks guys

Please don't, those offsets will look like complete AIDS on a R34

Edited by ~Hypnotik~

jesus this thread is a brothel!

you can run way better offsets than have been mentioned here...

i run 18.9.5 +30 (18x8.5+30 front) on an r33 gtst with no flare and near flat camber (just a roll) and its an easy fit... the 34 guards are bigger again, so 9.5 +20 will get you about the same fitment as me, and i still could go out a bit more... say another 10mm before i need to flare

DSC00011.jpg

Most people are way too conservative with offset. 33's can definitely fit +20 9.5" rims at the rear and +20 8.5-9 at the front with guard work and it will look a huge deal better than +35 and above offsets. Just don't run bulgy oversized tyres. 265-275 for 10", 255-265 for 9.5", 235-245 for 9", 235-225 for 8.5", 225-215 for 8". Any lower width and the rims are no good for a turbo skyline.

  • 2 months later...

R33 GTST easy but wide fit would be:

Front = 18 x 8.5 +30 235/40/18

Rear = 18 x 9 +30 245/40/18

A little roll at rear - with 1degree neg camber both front and rear.

Keep in mind that you don't want big changes in track widths front to rear.

R34 are a bit bigger so:

Front = 18 x 8.5 +24

Rear = 18 x 9 +24

Not that I can think of rims that are these exact sizes. I currently have 18 x 8 +30 and 18 x 8.5 +33 and they sit about 1cm too far in the guards on R33. Come tyre replacement time I will get 245/40/18 for the rear - up from 235/40/18.

Edited by simpletool

Hi,

I have not been sharing much since i came on the forum. I am from malaysia and here what i have for my setup.

18x9.5 +12 all around

F: 225/45/18 -1 camber

R:245/40/18 -2 camber

[ wheel was off a R34 GTR, got it cuz it was dirt cheap and thought the offset should be manageable]

I have not flared my guards so i been scrapping on hard bumps on all 4 wheels for a few weeks now. I am looking to get camber arm to help go negative even more. This is the part i need some guidance on. Now i have jacked up the suspension so the scrapping is to the minimum. There is a few people in here i have PM that helped me; it still work in progress.

post-51211-1248662237_thumb.jpg

Edited by k20aek

im running 18x8.0 on the front, unsure of offset i'd have to check with 235 rubber no guard work

and 18x9.0 +24 with 265 tyres no guard work.

back wheels sit flush, maybe stick out a mm or 2. looks good

thats on r34gtt

Edited by stenve
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • No. GKTech arms have spherical bearings in them. No bushes. You will not need bushes for those arms. The sphericals are a bit of a maintenance nightmare. I have replaced all of mine several times in the 5 or so years I've had them, and I have the arms out regularly to clean and lube the balls. Worth the pain on an R32, because the standard arm design is trash. If you need the camber adjustment, there are other options (than the GKTech ones), although I would still lean towards and prefer the GKTech ones, even with the maintenance load of the sphericals. The caster adjustment is also highly valuable, allowing for setting the car up to drive straight. There are a million options for these, including the GKTech ones. I've had Tein rods on mine for 20 years and the balls are much less trouble in that location. Never given me a moment's pain. All positives, no negatives. I consider them compulsory.
    • Lol yeah I ordered the clips mentioned and as far as the amayama diagrams go i think thats all I'll need. Fogured id ask, sometimes people's first hand experience doesnt always match up to diagrams haha, i guess I'll wing it and worse comes to worse I'll just deal with it as I go
    • Thanks for all that information I appreciate it. To answer your questions: - Yep that's what I mean. These guys are professional painters to so I must be missing something. It's a bit hard to explain. - With the primer landing on clearcoat, I make sure that the surrounding clearcoat is scuffed to 240 grit as my epoxy primer says that I only need to sand the area to 240 grit. - Yeah so similar to the first question, assuming that the paint landed on the unscuffed clearcoat because I've seen that happen. - Yep I want to prep the surface in that order. Only reason because epoxy primer will protect it from rust and I need that atm with this crappy Sydney weather. I think I was worried about time, if I try to put the filler down but screw it up somehow and I don't have time to sand it off and reapply it then need to put primer later that it might start to rust again so I wanted to apply the primer as quick as possible to not deal with rust.  - I just deleted some answers, I just realised after watching a video and what you said about looking at the data sheet, that I need to read the data sheet on the specific filler I'm using. It's possible now that I put epoxy primer first was a waste of time and need to go to bare metal lol
    • I did. I went to a suspension guy and he told me because I don't have adjustable camber arms it's the reason why my car veers towards the left if I take my hands off the wheel but if I drive my other every day car and take my hands off the steering wheel it goes completely straight. I think it's common with Skyline's. In order to fix the problem, I likely need gktech camber arms then nismo bushes since I have poly bushes atm, then a wheel alignment after that. With my car if I take my hands off the steering wheel on a really bumpy road before stopping at a light I have to hold my steering wheel somewhat tight otherwise my car will legit just go completely in the other direction quite quickly and I'll slam into something lol instead of stopping straight. I Believe this YouTuber had the same issue and fixed it with gktech arms. At timestmap 6:05 he talks about how the car doesn't veer anymore after installing these arms.  
    • hello! does anyone have a schematic that shows how to test the blower motor resistor for the vac system? i believe the part# is 27761-15U00. I think the resistor is toast, but would like to be able to test it somehow before i embark on the journey to find a new one. cheers! 27761-15U00
×
×
  • Create New...