Jump to content
SAU Community

Recommended Posts

DSC05526.jpg

the big yellow one?

my standard oil pressure gauge was showing low readings yesterday morning (1 at idle - 2 when driving)

then after being parked for 30 mins, the gauge showed normal readings (2 at idle - 4 when driving)

than again a few hours later the readings were low again.

i suspect (hope) it's the standard sensor playing up.

EDIT:

i cleaned the plug terminals with contact cleaner. they were clean anyway.

the gauge is now showing kinda normal readings, just a tad low on cold start. it use to creep up to 5-6 on the stock gauge, now it goes just over 4.

at about 3000rpm, warm, its just under 4. this is a bit lower than it used to be. idle is a touch under 2, as before.

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

Edited by Munkyb0y

i cleaned the plug terminals with contact cleaner. they were clean anyway.

the gauge is now showing kinda normal readings, just a tad low on cold start. it use to creep up to 5-6 on the stock gauge, now it goes just over 4.

at about 3000rpm, warm, its just under 4. this is a bit lower than it used to be. idle is a touch under 2, as before.

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

Hmm interesting, i used to get similar things with really low oil pressure. It would only do it now and then, like once a week. I would be sitting at a traffic light or something and then suddenly my oil pressure would go down to like zero and id be like ;) but there were no signs of any problems so i never thought much of it. Hmmm might check my sender aswell.

Where is the actual sender located? Im looking at that pic and have no idea where that is??? (Below the intake runners??)

Edited by PM-R33
my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?
How much oil is in the sump? How old is the oil? What grade is the oil?
How much oil is in the sump? How old is the oil? What grade is the oil?

less than 1000kms old. 7.5w30 genuine nissan semi-synth. dipstick shows full. car has never used oil between changes.

the stock sensors are renowned for being crap (in the GT-R anyway), mine goes to 0 sometimes (freaked me out the first time). But all i do now is flick the engine off and on, and the gauge works again. I'm gunna get a quality aftermarket gauge, as i don't trust mine as far as i can kick it.

I am in the same boat. One second it sits normal, then it drops to 0. Scared me to death eh.

How difficult is it to get to that oil pressure sender unit in the pic? I can picture it, but i have hands bigger than dinner plates, so it's super hard for me to even get my hands around the oil filter.

Yeah well you could all be like me..... thought yeah its just the sender , they are all crap and a common problem.

BUT, on rebuilding the motor from continuing driving when the screws had come out of the back of the oil pump and impossible to see,

it was REALLY the oil pressure being almost non existent that caused the big ends to start knocking and burning!

I certainly would not wish that on anyone so hope thats not your problem!

Maybe you should do what my son suggested and fit a proper mechanical Oil Pressure gauge and avoid the end disaster. :dry:

Can u just replace the sender or something? Its just i allready have 2 gauges in my car in a pillar, and would rather not get another gauge (oil pressure) to just chuck somewhere on the dash. If its just the sender, would a new sender fix the problem instead of getting an aftermarker oil pressure gauge?

you can change the sender, but you'll need a nissan or nissan compliant sender. otherwise the values it's sending wont be correct for the gauge.

just like you cant hook up an aftermarket gauge to the standard sender and expect it to work correctly.

i'm not too sure, but have read that the nissan sender costs quite a bit. defi gauge price range :D

my question is, is there something that would actually cause low oil pressure (1 at idle - 2 when driving), and then recover from this?

or is this almost certainly a gauge/sender fault?

i plan on getting an aftermarket gauge, but sandwich plate etc, it's gonna take a while. i'm guessing you have to drop the oil in order to do this. no way around it?

????? :)

i have a mint sender if anyone wants to make an offer on it.

it might be the sender, it might also be the dash guage.

at the end of the day unless you put a mechanical guage on it, you will not really know the pressures for sure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
×
×
  • Create New...