Jump to content
SAU Community

Show Me Your Racing Machines

screamin'
 Share

Recommended Posts

  • Replies 2.8k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

260DET
260DET

Try again with the motor pic, am I banned because its not an inline? Zed has a FJ20ET, great donk.

Posted Images

phunky_monkey Grand Master

phunky_monkey

Posted
Posted
Yeah single wastegate

Cool. If you wouldn't mind putting up a pic of it when you're done that'd be most appreciated! Keen to check that option out vs the Full Race kit.

Sav man: This is my Nismo one in my 25 box, but not sure how much of a S you're looking for.

post-8405-1254094946_thumb.jpg

sav man Grand Master

sav man

Posted
Posted
Don't all the shifters go into each 'box?

Benny, I reckon you'd need to make one mate, has YT got you sitting in the back seat?

not really, i was looking at trying to get a comfy position, and i think the gearstick might need to come back...so i don't need to have my legs cramped up

sav man Grand Master

sav man

Posted
Posted

just personal prefarance, like to have the stick close. but once the seat is in i might change my mind. just wondered how hard it was. if i had a pedal box, i'd move everything right back though....but i'm not even temped to spend that kind of money.

PHaT MR30 Grand Master

PHaT MR30

Posted
Posted (edited)
fancy stuff is for gtr's and porsches.

Just talk to K. Luck about putting fancy stuff on your gts, more problems and goes slower... keep it simple and keep it clean...

Edited by PHaT MR30
Beer Baron Grand Master

Beer Baron

Posted
Posted
Big little engine project is very close to completion now. Had a high-octane sump extension welded onto a factory sump last week so ive installed that today and finished cleaning up and installing a little more plumbing. The timing belt issue has been a bit more of a challange that I had thought it would be. The first belt ive sourced is 1 tooth too long, so im having to order a belt from the UK that normally goes on a vahuxall astra to get the right tooth count.

GTRS's should arrive next week so when the belt arrives it will be ready to install. Cant wait!

looking good mate. :thumbsup:

GTRNUR Grand Master

GTRNUR

Posted
Posted
looking good mate. :thumbsup:

Thanks Richard. In hind sight Im thinking I should have made a build thread for this engine, but I can always do that later I suppose. I've got timing belt on it now, all sorted. Its a little perverse what engine it came from though.... its an Opal (holden) Barina timing belt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Before starting any work, we attempted to adjust the tune. However even after adjusting it to certain extremes like completely stopping fuel, it had no effect. What fixed it was removing the Nistune Board and installing the original EPROM instead. This immediately fixed the issue. Everything should have been fine with the Nistune Board installation, so I am unsure why it has caused a problem. The soldered connector is also properly soldered. This worked when I first got the 550cc injectors, before cleaning, but that may have been a coincidence.  We ended up not installing the fuel pump hanger (at least for now). So currently running stock injectors, stock fuel pump, stock fuel pump hanger – Well everything stock except the exhaust. Now I have around €1400 in Nistune, Injectors, and Hanger collecting dust for the time being, perhaps I'll install them in the future. For now I'll enjoy the car as is 😁 Thanks a lot for all your assistance, I really appreciate all the help you have given me.
    • Piggaz
      Why am I hitting a power wall with my stroked RB25?

      By Piggaz · Posted

      The turbo can’t be the issue. They’re proven to make much much power than you’re making. There is something in the setup that isn’t correct. - has the exhaust got any silly step downs? - what exhaust manifold?
    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      Ok, just the way you wrote it made it look like you had the stagger the wrong way around 
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I was getting anxious with the DVLA not knowing if the paperwork is fine or not, so I rang them. No update had been given, but I  was reassured that providing the box was ticked on the V750 then the application will go through fine. I've been checking the DVLA website pretty much every day, in the hope that it would have been done. Fast forward to Monday 29th  and I was greeted with a new screen on the check, and it finally showed as Taxed and MOT'd, woohoo! The car was in desperate need of a clean, not knowing when this day was coming it was put off. As far as I was concerned I had another 3 weeks  I'm not normally one for using snow foam, but I wanted to give it another try It hasn't cleaned up too bad considering it's 21 years old and lived on a boat for a number of weeks. The personalised number plate is J2 XBK, an illegally spaced number plate would have it read J2X BK. BK could either represent  the colour black or Baker, which is my surname. I filmed the first drive, the Youtube link will be at the end. I used the same driving route I did with the 323F V6 when I had a new exhaust installed, heres a couple of photos A few more since then Youtube video can be viewed here: https://www.youtube.com/watch?v=TjkFHPzjGDw
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
×
×
  • Create New...