Jump to content
SAU Community

Recommended Posts

Hey guys

i have an R33 gtst which is fairly stock - FMIC, 3in exhaust, pod. i am currently chasing around 250 - 270 rwkw, car will be mainly used for street but also a bit of circuit and 1/4 mile.

i am in the process of buying all my mods and installing them all at once, saves me on ru-tunning costs.

So far i have bought:

720cc sard injectors (top feed)

sard fuel pressure reg

greddy fuel rail

bosch 044 fuel pump

greddy plenum chamber

haltech ECU

blitz dual selnoid EBC type R

cam gears + timing belt

All i want now is a high flow turbo and cams.

With the turbo i dont wont a huge lag machine but i want something that when boost kicks in ill get punched into the seat, plus it will help with getting of the line if the turbo isnt super responsive. Reading all the threads im inclined to get a HKS Gt-RS or a GCG high flow but dont want to spend 2k. is there any good garretts for around $1500 which will get me to my goal?

With cams not to sure whats good but i really want cams that will give me that nice tough engine note, nengun have some HKS cams: 97/8 Duration - 256, lift 8.8m http://www.nengun.com/hks/camshafts-nissan 2202-RN172 /3 which are fairly cheap but any suggestions will be great.

thanks

Link to comment
https://www.sau.com.au/forums/topic/178810-not-another-turbo-thread/
Share on other sites

I dont suppose your Series II is after a 97 model?

If so, there's some freegan cheap Cams in the for sale section.

Tomei Poncams for $600 !

I nearly went for em myself but it's just that bit extra cash i can't deal with right now, dealing with a new clutch and installation :(

The GT-RS is a hard act to beat.

A Garrett cartridge that would go close to the target using OE housings would be 446179-5032 - The 56T GT2871R. But you'd want a good idea of the costs of oil + water lines for the total cost vs HKS product.

Try a search on cams. There is plenty of comment about whether cams are justifiable at the power level you're targeting. I'd say the overall efficiency would lift with them but the raw numbers not show a large improvement from stock. At $700-$1000 fitted and installed you'd have to ask whether a changed exhaust note is justification enough.

Reading all the threads im inclined to get a HKS Gt-RS or a GCG high flow but dont want to spend 2k. is there any good garretts for around $1500 which will get me to my goal?

Nope.

$1750 at the bare minimum, and then add installation, dump pipe etc etc.

Around $2300 at least.

The GT-RS is a hard act to beat.

A Garrett cartridge that would go close to the target using OE housings would be 446179-5032 - The 56T GT2871R. But you'd want a good idea of the costs of oil + water lines for the total cost vs HKS product.

Try a search on cams. There is plenty of comment about whether cams are justifiable at the power level you're targeting. I'd say the overall efficiency would lift with them but the raw numbers not show a large improvement from stock. At $700-$1000 fitted and installed you'd have to ask whether a changed exhaust note is justification enough.

yeah i have read a few topics about the minimum gains from cams but later in the future i plan on doing forged internals so i might wait till then and get it all done together.

I have been going back and forth from the GT-RS and GCG highflow so many times it makes my head spin. Correct me if im wrong but you should be able to get the GT-RS kit for around $2500 so i was thinking get that then sell the standard turbo to recoupe some $$$ losses.

Anyone 2 wanna take me for a ride with each turbo so i can feel the difference :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...