Jump to content
SAU Community

Recommended Posts

Heya guys,

I picked up my new pride and joy on saturday and im loving it so far, alltho my mate took me for another run in his HR31 with RB20 red top and it is a SHIT LOAD quicker than mine and i cant work out why.

here are my specs

RB20 silvertop ECCS

Rb25 T3 turbo on 14psi

HKS cooler (600x300 ish with was looks to be 2.5" piping.

2.5" downpipe off turbo into a 3" system with two mid mufflers and a rear muffler (5zigen system) (no cat)

standard wastegate and factory bov

turbosmart controller (it is mounted on teh firewall, should it be that far away from teh turbo and the actuator?)

SAFC2 (not sure on how it has been tuned, wether on dyno or in driveway by previous owned)

normal GTST box and LSD diff with coilies and a massive pressure clutch, really bites :P

my mates mods

HR31 redtop RB20

Rb25 T3 turbo on 1 bar

600x300 cooler (unsure of brand)

3" system straight to a rear muffler with Apexi exhaust valve

HKS BOV and some electronic valve control thingo

bee*r

apexi Neo AFC (tuned for about 250hp aparently)

5 speed manual and lsd

we are both running exactly the same width tyres.

(its [THN] s old car (tuyen)

basically his scares the shite out of me, really gets up and boogies and it just pulls harder every gear however mine feels like it has 40hp less or more and splutters around 5K and is i feel it is slower than my 4agze running 13psi.

seeing we both run very similar gear i would expect mine should be a bit faster due to it being a Silvertop, but nooo

could i have a shitty tune on the afc? i just dont get it :thumbsup: i want mine to be as fast.

Edited by YEHBOI
Link to comment
https://www.sau.com.au/forums/topic/180666-my-rb20-st-vs-mates-redtop/
Share on other sites

thats why i thort i may have a shitty tune :S i used BP ultimate too.

im not overly sure but with me on my own it isnt even as fast, with both of us in his car which is an extra 80kgs his is still faster. both of them are kept pretty well factory sort of weight. (he doesnt have weight reduction or anything like that)

Edited by YEHBOI

Other than the obvious misfire you have, i'd suggest you have a more restrictive exhaust, and your mates car has a bit of tuning where yours doesn't. Then theres the fairly general term of "T3 turbo". Seriously it could be anything with a t3 flange on it.

  • 3 weeks later...

Obviously there could be many things as to why your car is not as fast. But it comes across as if you assume the silvertop "should" be faster.

The silver came out when all the emissions crap was going on etc. It had a BOV where the red didnt have to. Dont quote me but I think the eccs redtops were also cammed differently i.e more aggresively.

The redtop could of been freshend up in its lifetime where your silver could be on its last legs etc etc etc.

The ex gibson GTSR's run redtops and go just fine lol.

I thought the limit for the 33 turbo was 14.5 pounds??

any idea what a set of coils will be? i have a feeling im not going to get much change out of 2K for a set of brand new ones

Since you are running it on an rb20 you should be able to run 16-18 pounds safely, on the RB25 it's limit is around 1bar, depending on the wheel specs, as long as you have the ceramic and not the nylon wheel, you'll be fine

coils are quite expensive, you might only have one or two bad ones, you can get second handers quite cheap, or go for a wasted spark setup using VL coils and I used VN leads, works fine :( total cost was $140-160, or you could go splitfire for round $500

As for the spluttering, I think it does sound like an incorrect tune on the SAFC

You should:

Crank the boost

Get it tuned

Replace any coils if need be

Don't tell your mate :P

Also if you are running the standard dumppipe you might be restricting the flow, you could always opt for a 3"incher to the cat or a 2.5" with a seperate wastegate elbow which joins up somewhere down the front pipe

What sort of cat are you running? i've you've only got a catback exhaust with standard cat, you won't be gaining the full potential of your exhaust, I suggest if it's all stock, replace it with a higher flowing cat, or if it's legal in your state - rip it out :thumbsup: I've done that to all my cars here in NZ

Since you are running it on an rb20 you should be able to run 16-18 pounds safely, on the RB25 it's limit is around 1bar, depending on the wheel specs, as long as you have the ceramic and not the nylon wheel, you'll be fine

sorry champ there is a fair bit wrong with this statement, just thought i would clear a few things up...

1. On an RB25 with RB25 turbo you can run 12psi or on an RB20 with an Rb25 turbo you can run 14psi. no higher

2. In regards to the wheels. All RBXX turbos have ceramic turbine wheels. the difference is in the compressor wheel. RB20, series 1 RB25 run alloy iconnel wheels. series 2 RB25 turbos and Neos run nylon compressor wheels. there turbos are limited to around 12psi because the hugher shaft speed required for 14psi is enough to start delamination.

so the clear things up run an absolute max of 14psi. 12 would be safer.

cheers!

id say the spluttering would be coils, get a set of split fires as already suggested, get a 3" dump and you have way to many mufflers in your exhaust. id get a good high flow cat and get the 2 mid mufflers taken out. or forget the cat and still get the two mid mufflers removed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...