Jump to content
SAU Community

Recommended Posts

  • 2 months later...

Just a quick question for you ppl who have installed the freddy manifold, I pulled mine off the other day and noticed I only have 4 bolts underneath holding it on out of the 6 there , anyone else only using 4? I can't remember why I only had 4 on maybe 2 of them didn't line up with the head ?

I'm using all 6 and everything lined up fine. And it is a bit of a pain to do in the car. It's not so bad once you just accept the fact that it's just going to take you all day to do 10 bolts up and crack a few tins while you do it :)

thanks for the quick replies, once i get manifold back i will attempt to line them all up. my manifold was one of the first ones available on market like 5yrs ago, so maybe the newer designed ones are better not too sure!

ill report back

  • 4 months later...
  • 6 months later...
  • 2 months later...
  • 9 months later...

Big horrible thread bump lol.

 

has anyone any other options/links for this or a similar thread? Started my install ages ago and only getting back to it now And haven't a clue how it all went together

the link above for rb26.net doesn't work now either ?

Any help appreciated,

thanks. 

Noone at all save the pictures from it? Even bits and pieces from when you did your own install?

To be more exact, the bottom pipe of the is iacv? Where does it go? IMG_4821.JPG.17576f43860de7d4bed2b7af66bec562.JPG

Which nipple does he extend the turbo water lines to in the guide? I have mine running off the pipe he blocks off beside the thermostat?

what 2 wires need extended?

What is the welded piece of galvanised tube for the aac that's mentioned about?

If anyone could help it'd be massively appreciated. 

Surely someone was smarter than me and saved the thread for offline use....

 

 

Edited by Ep82jm
  • Like 1
  • 4 months later...

That open tube you have needs to be plumbed in upstream of the throttle body . Its the air supply for the Idle Air Control Valve . In standard form it connects to a barb on the original crossover pipe - upstream of the throttle body .

A .

 

 

For everyone playing at home, its actually pretty simple to do. When you have all the parts and are trying to put it all back toether it makes sense and can only really go together one way. Utilising your brain and the desciption that ix9 provided you can do it.

Bumping this 10 year old thread and asking the OP (who hasn't been online for over a year) for pictures that he has said he ne longer has is proooooobably not going to yield any results. Have you actually searched through this thread as i know for a fat they have been rehosted somewhere else online at least once or twice.

images?q=tbn:ANd9GcRQ8qfJJYb7mq5_jmPHOMX

  • 5 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Haha luckily we don't have emissions, inspections, or any laws against power adders here. They only thing they somewhat keep an eye out for are ridiculously loud exhausts. 
    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
×
×
  • Create New...