Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

lol ok here we go again....

to put it simple... previous owned HAD a GTR badge on it and put an apexi one on it.. I riped it off cos i hate badges. I then see an impression where a GTR badge used to be which was very easy to see.. so i covered it up with another badge until i get it sprayed..

lol ok here we go again....

to put it simple... previous owned HAD a GTR badge on it and put an apexi one on it.. I riped it off cos i hate badges. I then see an impression where a GTR badge used to be which was very easy to see.. so i covered it up with another badge until i get it sprayed..

rust hole in boot would be more appealing than a fake gtr badge

Without the Wing looks really sleek and smooth.. but what about Downforce @ high speed?? more Stabilty..

Yeh take off the GTR.. make it a Sleeper.. hehe :D

I would take off the wing if downforce didn't matter @ high Speeds

-SeS

Edited by Black_CSR

de-badged and de-winged FTW!

quick question, i have a s2 r33, so its got the big square wing, how do i take it off?

i noticed the rubber covers over the bolts on the under side of the boot lid but there seems to be some sort of adheasive attatching the wing to the boot..

can i just rip it off or do i have to do something special? i wanna put one of the small lips on it so i dont have to buy a flush boot lid..

:rofl:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
    • your right the maps for Australia came out in 2017 but are 2010 maps. i got the updated maps SD card put it in and it was the same. Same maps in my Brothers Nissan Patrol. 2020 i think his car is
    • Yeahhhh, the costs have killed me. Spent more than the cost of an engine rebuild and it most mostly servicing and a tune lol.
×
×
  • Create New...