Jump to content
SAU Community

Recommended Posts

It get's blocked up.

I've been lead to believe that if you clean it out, use good oil and service it regularly you should be fine.

To be safe, if you're running a standard turbo you can drill it out to 2mm, and if you're running a highflow you drill it to 3mm.

Scotty and Aaron are the experts, but that's what I've been lead to believe.

Any peeps on here interested in a wood trim interior for an M35? I only ask as I'm going to paint it all black unless someone wants to trade...

:)

You can vinyl wrap the timber part of your dash and it looks pretty good.

I would just drill it out to 1.5 mm if you plan to keep the stock turbo, 2.5 mm if hou go for a bushed core.

The banjo threads into the block just in front of the passenger front drive shaft.

It get's blocked up.

I've been lead to believe that if you clean it out, use good oil and service it regularly you should be fine.

To be safe, if you're running a standard turbo you can drill it out to 2mm, and if you're running a highflow you drill it to 3mm.

Scotty and Aaron are the experts, but that's what I've been lead to believe.

Great info, thanks guys. Might drill it out when I go to see my old man in a few weeks since he has a drill press. I don't even have a vice at the moment!

I don't suppose some one on here knows if the centre console on an M35 is interchangeable with the V unit? Chasing both the radio surround and lower gear stick surround. Figured if they are interchangeable it would make finding these parts a million times easier. :)

I don't suppose some one on here knows if the centre console on an M35 is interchangeable with the V unit? Chasing both the radio surround and lower gear stick surround. Figured if they are interchangeable it would make finding these parts a million times easier. :)

yes, they are both inter changable.

I saw one for sale on the V series forum

Well I've set mine to 360mm front and rear, this gives about 15mm gap between tyre and guard with my 245/45-18 tyres. I might drop it another 5mm but probably not worth the trouble. I like to leave 10mm gap so it doesn't get too many looks. With the aero front bar it just clears those cement stops in car parks. Its funny, when I look on the RAWS site and look up my car it shows the stock height (i think its listed wrong) and minimum height. It states unladen F and R 365mm and Minimum F and R 346mm. I had it at 345mm at one stage and its bloody low so I think the figures are wrong.

Edited by slippylotion

Rear under spoiler for the left and right muffler system

I haven't seen any mention of this here before therefore I am just shariing in case someone want to take this path...

http://global.rakuten.com/en/store/zeesis/item/m35-supoir/

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...