Jump to content
SAU Community

Recommended Posts

If the tune is correct and you have a bit of headroom in the injector, you shouldn't have an issue.

If your maxing out your duty cycle and your cheating by bumping up the base fuel pressure just make sure the flow pattern of the injector is still up to spec. Some injectors get very messy when you up the base pressure. I prefer standard base pressure and run the CORRECT sized injector for the application.

If the tune is correct and you have a bit of headroom in the injector, you shouldn't have an issue.

If your maxing out your duty cycle and your cheating by bumping up the base fuel pressure just make sure the flow pattern of the injector is still up to spec. Some injectors get very messy when you up the base pressure. I prefer standard base pressure and run the CORRECT sized injector for the application.

I'm with you on that paul

Sounds good then.

I'm getting close to maxing out the AFM, but injectors should be fine.

For me, this is a decision between throwing in the ID1000s now, or when I eventually do an E35 tune. If I need them now, I'll put them in. But sounds like I don't?

Car is running stock turbo and only half an intake pipe. Not the most serious mods.

I would agree with you on the injectors Leon as even at 18PSI with my car my Wideband never gets over 10.8 unless under load going up a hill then is gets to 11.1. However the AFM is well and truly maxed giving readings of 5+...and I know my duty cycle is over 95% at times....I have also seen 100% quite a bit......I can live with that on the street as I am hardly ever up it.

However I would never track it without bigger injectors and the AFM clamped.

P.S. I think its awesome how the car has worked out its tune with the extra pressure at 14v with the Walbro on mine....it would be very interesting to try a set of 440cc injectors in the car with the standard fuel pump to see if/how it runs.

Craig, I am impressed that your car runs so well on stock injectors, with just the fuel pump pushing more through (thought you might've surpassed that). I'm still tuning mine (adding fuel mainly) but my max injector duty cycle is 90% as of today. After the intake went in, but before the FPR, it was close to 100% on occasions.

I think 440cc injectors & standard pump would be a similar result to the opposite (Walbro & std inj). Do you think the ECU would learn it over time?

And Paul, I too agree. In a perfect world with lots of spare time and/or cash you would correctly size the injectors & leave fuel pressure alone. But the point I was making was that it wasn't necessary to stress over injector sizing with the mods that I or Ryan have done thus far. Especially since upgrading the fuel pump gives higher pressure as a by-product. Can't see anyone would change the FPR to a lower pressure just to counter the new pump, lol.

  • 3 weeks later...

There is a few Hypergear turbos getting around, I doubt any have been tuned so don't take the power output too seriously, yet.

Near factory response is hard to believe too, it looks about the size of a Sierra stage 1 so it will probably come on around 3k. Not a bad price though Stao. :thumbsup:

There has been bit development in that high flow as I had a customer whom own a work shop near by was happy to trail all of the combinations and the best felt on road is some thing in between a 3071 and 2871 with custom trimmed up turbine wheel with FNT turbine modification. It is touch smaller then the usual profile that I normally run in the skyline turbos which some of you noticed the HP rating isn't as high.

I've also modified the bearing housing so they can work with stock oil supply, braided oil line is no longer required.

Test car was a auto M35 with cooler and exhaust only and that high flowed turbo was excellent to drive with on road. I believe the best option is running the SS1PU on the VQ25. I'm consider making a custom mould for when more M35s comes into the country.

The stock housings flow ok, all you need is a spare set so the wait time is reduced. I haven't seen any of these turbine housings cracking yet either Stao which is good.

Someone fit one and get it tuned... :D

  • 5 weeks later...

Can anyone who has installed a power steering cooler tell me where the best place is to connect the cooler?

Anything fancy that's required or just replace fluid at the same time?

Hasn't been replaced yet, figure I can use the Valvoline auto trans fluid I've got left.

Loop it through one of the lines going into the bottom of the radiator

no dont do that, thats for the transmission cooler circuit.

put it before the pump, you can use the hoses running up the the filler bottle. keep the stock ones, and just replace the hose with good quality type

no dont do that, thats for the transmission cooler circuit.

put it before the pump, you can use the hoses running up the the filler bottle. keep the stock ones, and just replace the hose with good quality type

Cheers Iain. Do you know offhand what size the hose is?

Thanks!

  • 2 weeks later...

Does any one know if the VQ35DE airbox is the same as the VQ25DET airbox? Or is they can be swapped?

Same airbox(PM35,V35,NM35,G35).......but the VQ35 comes with a power duct I think

Edited by Jetwreck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...