Jump to content
SAU Community

Recommended Posts

If the tune is correct and you have a bit of headroom in the injector, you shouldn't have an issue.

If your maxing out your duty cycle and your cheating by bumping up the base fuel pressure just make sure the flow pattern of the injector is still up to spec. Some injectors get very messy when you up the base pressure. I prefer standard base pressure and run the CORRECT sized injector for the application.

If the tune is correct and you have a bit of headroom in the injector, you shouldn't have an issue.

If your maxing out your duty cycle and your cheating by bumping up the base fuel pressure just make sure the flow pattern of the injector is still up to spec. Some injectors get very messy when you up the base pressure. I prefer standard base pressure and run the CORRECT sized injector for the application.

I'm with you on that paul

Sounds good then.

I'm getting close to maxing out the AFM, but injectors should be fine.

For me, this is a decision between throwing in the ID1000s now, or when I eventually do an E35 tune. If I need them now, I'll put them in. But sounds like I don't?

Car is running stock turbo and only half an intake pipe. Not the most serious mods.

I would agree with you on the injectors Leon as even at 18PSI with my car my Wideband never gets over 10.8 unless under load going up a hill then is gets to 11.1. However the AFM is well and truly maxed giving readings of 5+...and I know my duty cycle is over 95% at times....I have also seen 100% quite a bit......I can live with that on the street as I am hardly ever up it.

However I would never track it without bigger injectors and the AFM clamped.

P.S. I think its awesome how the car has worked out its tune with the extra pressure at 14v with the Walbro on mine....it would be very interesting to try a set of 440cc injectors in the car with the standard fuel pump to see if/how it runs.

Craig, I am impressed that your car runs so well on stock injectors, with just the fuel pump pushing more through (thought you might've surpassed that). I'm still tuning mine (adding fuel mainly) but my max injector duty cycle is 90% as of today. After the intake went in, but before the FPR, it was close to 100% on occasions.

I think 440cc injectors & standard pump would be a similar result to the opposite (Walbro & std inj). Do you think the ECU would learn it over time?

And Paul, I too agree. In a perfect world with lots of spare time and/or cash you would correctly size the injectors & leave fuel pressure alone. But the point I was making was that it wasn't necessary to stress over injector sizing with the mods that I or Ryan have done thus far. Especially since upgrading the fuel pump gives higher pressure as a by-product. Can't see anyone would change the FPR to a lower pressure just to counter the new pump, lol.

  • 3 weeks later...

There is a few Hypergear turbos getting around, I doubt any have been tuned so don't take the power output too seriously, yet.

Near factory response is hard to believe too, it looks about the size of a Sierra stage 1 so it will probably come on around 3k. Not a bad price though Stao. :thumbsup:

There has been bit development in that high flow as I had a customer whom own a work shop near by was happy to trail all of the combinations and the best felt on road is some thing in between a 3071 and 2871 with custom trimmed up turbine wheel with FNT turbine modification. It is touch smaller then the usual profile that I normally run in the skyline turbos which some of you noticed the HP rating isn't as high.

I've also modified the bearing housing so they can work with stock oil supply, braided oil line is no longer required.

Test car was a auto M35 with cooler and exhaust only and that high flowed turbo was excellent to drive with on road. I believe the best option is running the SS1PU on the VQ25. I'm consider making a custom mould for when more M35s comes into the country.

The stock housings flow ok, all you need is a spare set so the wait time is reduced. I haven't seen any of these turbine housings cracking yet either Stao which is good.

Someone fit one and get it tuned... :D

  • 5 weeks later...

Can anyone who has installed a power steering cooler tell me where the best place is to connect the cooler?

Anything fancy that's required or just replace fluid at the same time?

Hasn't been replaced yet, figure I can use the Valvoline auto trans fluid I've got left.

Loop it through one of the lines going into the bottom of the radiator

no dont do that, thats for the transmission cooler circuit.

put it before the pump, you can use the hoses running up the the filler bottle. keep the stock ones, and just replace the hose with good quality type

no dont do that, thats for the transmission cooler circuit.

put it before the pump, you can use the hoses running up the the filler bottle. keep the stock ones, and just replace the hose with good quality type

Cheers Iain. Do you know offhand what size the hose is?

Thanks!

  • 2 weeks later...

Does any one know if the VQ35DE airbox is the same as the VQ25DET airbox? Or is they can be swapped?

Same airbox(PM35,V35,NM35,G35).......but the VQ35 comes with a power duct I think

Edited by Jetwreck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...