Jump to content
SAU Community

Recommended Posts

there are a few options to be able to do burnouts

1. sell your stagea and get a commodore

2. grow up and dont try to do burnouts in car designed for AWD

+1

commodores are not my friend, chocolate is!

I'm too old to grow up, and I am quite iresponsible

My car is RWD

oh and I'm a drifter, D1NZ

LOL @ discipline fail

Haha

So is there any use asking for tech help on this forum. or is this an anti-fun forum.

Plans are to do suspension, shocks and springs, swaybars, nolathane bushes and brakes.

What I want is the car to be able to do a skid if I want to, it will not be a drifter, I have a race car or two for that, it's my daily after my C34 tow car got worn out.

Me at a Drift Demo

Me at our local track, practice

Not anti fun at all, most of us love skids. But skids and speed off the streets. Most of us live in areas that imports are pretty heavily targeted by the authorities, and as a community we want to promote off street activities. Search YouTube for some SAU texi vids for and example.

So when you just ask how to do skids, don't be suprised by the response! Most people reserve skids for kids with flat caps in commos.

So, to the car. If you bought a 2.5 or 3.0 and trying to do skids, your a derp. If you bought a 3.5 then you have some options. You can go down the NA bolt on route. Exhaust, plenum spacer, z tube, maybe a tune if your rich. That might get you to skidville. Other options are turbo or supercharger kits.

Best thing you could really do with a rwd, is a manual conversion. Just do it from a manual v35 wreck. Skids would be much easier, and more fun to drive.

Don't worry about the brake wire cut, in NA cars it doesn't exist.

Cheers Stagea Cuz.

Off the 'skids' topic for a sec, does anyone have any advice on the most appropriate place to fit a sender for a transmission temp gauge?

Looking at the box, theres two possibilities I could see:

One at the back just above the sump

ec8c9d0e.jpg

And another on the side near the lines to the radiator, but it might be a bit close to the front propshaft depending on how big the sender is

da555f0d.jpg

Anyone fit one before that could tell me which is the best spot?

I'm just doing an inline one, brass bspt barbed air fittings for the trans hose and 1/8 bspt for the sender thread. I only plan to monitor the trans temps, but the other inline sender for the new -12 engine oil cooler lines will control the thermo fan. (its mounted right behind the engine oil cooler.) I will get some pics when I re-install the engine.

I think I've seen them mounted in the side of the pan. Can't quite picture the locations you've supplied, but I'd be wary because the valve body sits pretty snug in there. Better of in the pan of fluid I would have thought.

I think I've seen them mounted in the side of the pan. Can't quite picture the locations you've supplied, but I'd be wary because the valve body sits pretty snug in there. Better of in the pan of fluid I would have thought.

That would be my choice; weld or braze a bung in to the pan.

The other thing; I wouldn't be surprised to find a spring & detent ball behind one of those bolts...

Edited by Daleo

Haha

So is there any use asking for tech help on this forum. or is this an anti-fun forum.

Plans are to do suspension, shocks and springs, swaybars, nolathane bushes and brakes.

Welcome Darren. Nice vids btw.

Don't worry, you'll get plenty of tech help here (& on itsnotavolvo.com.au) & a small amount of ribbing occassionally, as you've seen. It's all in fun & (mostly) everyone on here are good blokes with heaps of knowledge between them. Being mainly family guys &, ermm, responsible types, you will never hardly ever hear us talk about driving illegally. It's what sets us apart from the others :)

the only worry i have about the sender sitting on the side of the pan is ground clearance - my car is stupidly low at the moment :/

last thing i want is the sender getting torn out while my wife negotiates an Everest sized speed hump & leaving a trail of gearbox fluid all over the street where it doesnt belong...

the only worry i have about the sender sitting on the side of the pan is ground clearance - my car is stupidly low at the moment :/

last thing i want is the sender getting torn out while my wife negotiates an Everest sized speed hump & leaving a trail of gearbox fluid all over the street where it doesnt belong...

If you're worried about that; you (I) could roll a piece of sheet steel as a shield around the underside of the bung & sensor & weld on to the pan.

I don't think it would be an issue TBH; Jetwreck would be able to tell you if he's ever seen a pan with gouges or dents, mine didn't even have a stone chip in the paint.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...