Jump to content
SAU Community

Recommended Posts

  • Replies 181
  • Created
  • Last Reply

Top Posters In This Topic

If it's still ok to do at BMT ... ???

Can we stick to that as everyone's worked out details (finally)...

If not i dunno where BBQ can be.

Buti might have an idea for a cruise.

Form there to Sunbury... down back to cambellfield and off somewhere else.

The 31 club did it a while back and i went for half of it, wasn't too bad actually. Stopped at the airport to watch planes :D

Hey Guys,

Even if the Dyno part of the day isn't on we can still hook up for the BBQ at BMT if its cool with those guys.

Its a car friendly business and isn't as likely to attract as much attention as a group of imports at a Maccas.

The whole point of the day is to raise $$$ for MAS so we may as well go ahead with it.

AT the very least we'll get a cool BBQ and ( in my case ) get to meet every body.

So unless its called off completely, I'll see you guys there at around midday.

:uh-huh: :uh-huh: :uh-huh: :uh-huh: :uh-huh: :uh-huh:

QUOTE:

"Meet up at BMT is ok, but due to the current problems we would like to request that every one be as quiet as possible when in the vecinity. I look forward to seeing you all, there is a suitable outdoor area for the BBQ over the road. Appologies again for the inconvienience, but I assure you that when the sound barriers are in place ... BMT WILL BE ROCKIN TO THE SOUND OF TURBS SPOOLIN UP ON THE ROLLERS!!!!!!"

Dr_Drift

Originally posted by Al

I will still be coming!!

Just found out, BMT is a 5-10min walk from my work :)

nismoR34

Can you please bring your db meter, PLEEEEAAASE!!!

C ya all there!

Alan

No probs Alan, although we will probably have to still keep the noise to a minimum.

I will bring it along and see how it goes on the day.

Dont wanna cause trouble for BMT :D

Dale.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...