Jump to content
SAU Community

Recommended Posts

Well, we don't quite live in Germany though I wish I did at this time of year but the next best thing I can find is...

chalk_ad.jpg

More info can be found here - www.melbourneoktoberfest.com.au

Looks like it should be a top event so I'm gonna head down and check it out but I can't drink copious amounts of beer from 1ltr steins without some support so who's keen to come lend a hand to...

"SAU - Team Oktobefest 2007"

beerfest2.gif

It's on -

Saturday 27th of October

12pm - 11pm

I'll be heading down on the Sat 27th @ 12:30pm.

Tickets can be purchased from "Ticketmaster - CLICK HERE" Better get in quick if your keen to come.

I'll keep a list here of who's keen/has tickets and I hope to see some of you there! :D

nat_faxon17.jpg

Have tickets -

Adz + Dee

Evan

Bec +1

Brenton

Mav

Daz + Lisa

Adam

Tony

125255__beerfest_l.jpg

Might go but "Das Boot" scares me -

Brisby

Jarrod

Al

Ash

JVP

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

alrighty I'll be going on the sunday with my gf from QLD. Anyone who feels they can challenge me in the beer drinking stakes is welcome to come have a brew with us. the more the merrier, and I daresay we will be pretty bloody merry!

Edited by Ricey

LOL - we've learnt from previous experiences that we should'nt drink on Sunday's unless we have the Monday off - Grape Grazing was a tough lesson.

Saturday's on the other hand...... look out Dandenong!!!

I'll be in this Adz - will check with Stu tonight to see if he's keen.

Guess i'll see you ho's down there... few mates are going and seeing as it will probably be the last time i will be allowed out to such events for say... 15 years... gonna go down myself :thumbsup:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
×
×
  • Create New...