Jump to content
SAU Community

Recommended Posts

Hey guys, is there any tips for cleaning engine parts after stripping them off? I have been soaking them in degreaser and cleaning mine so far with good results, but is there anything else I can do to get them to come up like new? I was thinking of using CLR but it seems like a fairly general purpose product and not confident it wil do any better than degreaser. Thoughts??

Use degreaser, it is the best bet. I usually wash my parts in hot soapy water and rinse in clean warm water and dry if I want/need to get the degreaser residue off. Most degreasers are either phenol, TCE, PCE, caustic or more commonly kerosene based. All derivatives are made up of what they call abrasive products - that it, they are not new engine friendly. You can use degreaser as a first clean, but I'd finish with another product that removes degreaser residue.

You could use a few products, but water etc is the cheapest. Don't leave any iron/steel exposed for too long though, get it dry and coated with a light oil.

BTW I have mates that use degreaser and nothing else, and it works for them, they generally use a light running in oil and then do an oil change early.

I wouldn't soak things in degreaser for too long [depending on the degreaser base type], it could affect certain alloys.

This is something that i have been looking into alot recently.. with little results

Cleaning off baked on oil under cam covers is the main reason i needed this info.

1st try - Kenco water based degreaser mixed 1 part to 20 parts water - worked but not well enough after soaking for 48 hours. These are cast alloy cam covers and at this mix, no corrosion present.

Trying to get a hold of parts cleaner fluid, but cannot find this in any retail store and my Mech has it for $60 for 20L (brand unknown to me)

Spoken with a polisher who is getting in some new stuff to try, but thats $150 per 20L - so will wait for results from them

Currently left the parts with my Machinist to run in his engine bath setup - get them back tomorrow and see how they turned out.

Carbie Cleaner worked awesome, but not very cost effective to use the cans of that @ about $20 a can. i think i recall someone telling me about getting tubs of this stuff, that they soak carbies in, but depending on the parts size and how often you use it, this might be overkill

Kero - kero and diesel works, MR 30 - how is the smell of the shop area you use this in? is it individual parts or setup in a parts washer?

i use R55 solvent. it cleans really good and dries almost instantly and then you can pretty much eat off the product you've washed. if you get dermatitis or other skin irritations but DO NOT USE IT it'l f**k your hands up. then if its gona sit for a while light coat of oil

citrus cleaner followed by penetrant oil to make sure it don't rust while you have things in the open.

What type of citrus cleaner? and where from?

i use R55 solvent. it cleans really good and dries almost instantly and then you can pretty much eat off the product you've washed. if you get dermatitis or other skin irritations but DO NOT USE IT it'l f**k your hands up. then if its gona sit for a while light coat of oil

Where would you purchase this?

if it dries quick, then it will flash dry if kept in a parts washer ?

baked on oil.. the absolute best thing i have ever used is subaru upper engine cleaner.. however this stuff is abotu $20 a tin and it works great spray on baked on oil.. scrub with tooth brush or brush of somesort than wash it off with water and brings it up like new.

Edited by rb26s13

I've heard of saoking in diesel, but I seem to remember that you had to be careful how long you soaked it for.......

Also soaking in...........molasses [or a water based mixture of] of all things. Apparently this works [i've never tried it] but rumour has it it will eat alloy=====NOTE: This is only a word of mouth method, I've never used it, it may come up on the www.

R55 solvent you can get from most oil companies. we buy it in 44 galon drums and it costs bout $4 a litre. we also have a parts washer at work an use a water an hvy duty soap to wash stuff an that comes up pretty clean also

Kero - kero and diesel works, MR 30 - how is the smell of the shop area you use this in? is it individual parts or setup in a parts washer?

I bought "Low Odour Kero", was about $18 for a 4 litre drum from Bunnings. I just cut a 20 Litre drum in half and soak larger parts in there and have some smaller cake tin size ones for smaller parts. Use a scouring pad to get the muck off.

Some good points of kero is: it doesn't evaporate, its not highly flamable, after use you can strain it and re-use it.

For larger aluminum parts which are stained and corroded (like say my inlet manifold), i couldn't really do much, took it round a few engine builders and none of them have a bath suitable for aluminium, tried another place, which from their ad in the yellow pages looked really good, however they have always been closed whenever I called or visited.

I resorted to then getting it bead blasted and plated, which originally I didn't want to do, but after speeking with them and seeing their work it was a good move. Costing rounghly $200 for manifold/plenum and fuel rail. This won't stain/corrode etc and it doesn't look half bad either. Will post pics when I get it back.

I had previously used brake cleaner and carby cleaner, but its not exactly practical for the price and I like my lungs the way they are.

we buy it from leader lubricants or some business like that in perth. before that we bought it from fuchs. ive been using it for 5 years now all it does is dry your hands out but if your use that hand blocker cream or moisturiser or wash your hands with natural soap its ok. when its really dirty it makes my hands itchy. in winter its f**ked to use cos it just soaks in the cold and in summer it evaporates heaps quick. as i said in an above post DO NOT USE IF YOU GET SKIN IRRITATIONS EASILY..

we buy it from leader lubricants or some business like that in perth. before that we bought it from fuchs. ive been using it for 5 years now all it does is dry your hands out but if your use that hand blocker cream or moisturiser or wash your hands with natural soap its ok. when its really dirty it makes my hands itchy. in winter its f**ked to use cos it just soaks in the cold and in summer it evaporates heaps quick. as i said in an above post DO NOT USE IF YOU GET SKIN IRRITATIONS EASILY..

sweet cheers mate

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...