Jump to content
SAU Community

Recommended Posts

What's going in that monster? Looks tough.

was going to be stroked windsor 351 - 427 with twin T04Z's but we have been approached by a certain manufacturer to build something else, so i'll let you know the minute its settled.

  • Replies 812
  • Created
  • Last Reply

Top Posters In This Topic

that looks like it was meant to be.....notice the fogger and solenoids. i like the way this boy thinks.

yeh baron, hoping it will all be worth it. will no soon enough.

lol. that is pretty cool. finally get that decent engine into a decent chassis. >_< I like it.

can't wait to see your thing rumbleing along stu. it will definitely rock.

haha, thanks for the warm welcome guys. my journey to the dark side is complete.

the guys in the drag section were getting confused when i started doing susupension & brake upgrades.

at least you guys understand whats going on.

Good to see the sig has been updated acordingly.

'Drain, I took him to watch some circuit racing on the weekend..........Conversion complete.

can we change the thread title to "drag setup/circuit setup conversion" ?

Good to see the sig has been updated acordingly.

'Drain, I took him to watch some circuit racing on the weekend..........Conversion complete.

can we change the thread title to "drag setup/circuit setup conversion" ?

I see whatever you happen to have is contagious, Jase.

Shame. Stu was such a good bloke once upon a time, too!

:D

noooooooooo, have you seen him drive?

It's ok Adrian, there is still time to swap the auto back to a manual and since you haven't tubbed it yet, we can still get it to handle around a corner mate :ninja:

have been looking at intake manifolds for a while, the Harrop item was looking like the go

but after some research it was found that it would be difficult to adapt different length ram tubes to it as it was designed to fit in the commodore and this is not an option due to bonnet height etc. harrop was also very difficult to get in contact with as they do not return faxes or email. obviously dont want to sell any.

Came across another Australian made intake, well priced and is designed for interchanging ram tubes. i also know the guy who spins them up so can get a few sets made. once car is back on the ground and engine fitted im hoping to get one of these babies.

post-20078-1225021415_thumb.jpg

it depends on those that are doing stuff for me, example wiring, exhaust. i could have it together in a couple of days.

but still no cylinder heads. also waiting for a few front suspension bushes, so probably a month off.

when do you think you will have it ready to run?

recieved the best news ever today, my cylinder heads are ready. measured piston to cylinder head clearance and found we have to run a slightly thicker head gasket. cc'd the head and worked out comp will be around 11:1 if we deck 20thou of the head while still maintaining 80 thou piston to valve clearance. should have everything ready for assembly tomorro night.

recieved the best news ever today, my cylinder heads are ready. measured piston to cylinder head clearance and found we have to run a slightly thicker head gasket. cc'd the head and worked out comp will be around 11:1 if we deck 20thou of the head while still maintaining 80 thou piston to valve clearance. should have everything ready for assembly tomorro night.

Sounds like excellent news!

11:1 is a good compression ratio, a little higher than original...

Cant wait to see/hear a video of the engine roaring...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
    • I believe @Duncan has given it a crack at Mt Buller before (in actual race conditions)
×
×
  • Create New...