Jump to content
SAU Community

Recommended Posts

Life Story entry #326:

Happy I got the Stag back. The box feels much better. Gotta head south to run a few errands today. Might head home via the hills on the way back :)

Image324.jpg

bargain basement. this + control box + reversing camera for 165 delivered to my door

win

oh yeah, gotta fit it yet haha

wwhhhyhyyyyyyyyyyyy matty whyyyyyyy. i used to sell that same model at autobarn for 130 on sale. shoulda come to me if you were ebaying for something like that. coulda put together something for under $100. Did it come with the wireless camera on the bracket that just bolts over your number plate or did they give you a proper cmos wired camera?

wwhhhyhyyyyyyyyyyyy matty whyyyyyyy. i used to sell that same model at autobarn for 130 on sale. shoulda come to me if you were ebaying for something like that. coulda put together something for under $100. Did it come with the wireless camera on the bracket that just bolts over your number plate or did they give you a proper cmos wired camera?

came with bracket to mount the screen, wiring (with 2 inputs), remote control (f**k knows why i'd need that), 10 metres of cable and a small sized cmos wired camera. im getting a CCD camera for the trailer when i get round to it.

ah yeah sorry Jack. I am after a stand-alone screen that I can have a fibreglass shroud built to custom mount it on a dash. Planning on plugging an EeeePC/Acer Aspire One into it to run full time consult display tools from ODBII. Resolution needs to be around 1024x600 or so, and needs to have a VGA conector (and USB connector to run the touch screen obviously).

ah yeah sorry Jack. I am after a stand-alone screen that I can have a fibreglass shroud built to custom mount it on a dash. Planning on plugging an EeeePC/Acer Aspire One into it to run full time consult display tools from ODBII. Resolution needs to be around 1024x600 or so, and needs to have a VGA conector (and USB connector to run the touch screen obviously).

Sounds sexy Andrew, will fit the new car quite nicely too!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...