Jump to content
SAU Community

Recommended Posts

the whole interior of my car is a blur of blue neon lights

despite the riceness i love them

i want to finish the car off buy putting on those blue neon windscreen washer nozzles

does anyone know if they are legal/illegal

and are they hard to install :S

Link to comment
https://www.sau.com.au/forums/topic/188788-neon-windscreen-washed-nozzles/
Share on other sites

i got pinged for having blue ones on my old s13.

i was told by the 50 that :"it is illegal to have any aftermarket emergancy vehicle coloured lights. (red, blue,)"

but i believe thay can also argue, ur leds are a distraction.

i know that it is illegal to drive with them. but if your not you can have wateva u want going off.

i had red ones on my commodore... got in trouble over them... some cops will tell you you can have them when your parked and others say not at all, my missus had them on her lancer... apparently if they are white lights on the bonnet they are legal, but some cops still argued the point.

just add, if you have coloured or thinking of having coloured lights for rear eg. number light surround... we were told they have to be red and only ingauge when breaking... but to avoid trouble, best not fit them at all

:thumbsup: my dream is fading

i really want this, i think its would be like the final accessory for my car. but i don't like this illegalness

ive seen the white ones and they just look bad...

im sure all the lights i have on the interior are illegal. maybe its best not to tempt fate

Illegal in melbourne too. Forward facing lights must either be amber for indicating or between 5500K and 6000K (or something like that) basically regular headlight white.

besides, everyone will think you're the biggest tryhard ever if you put them on. The police are doing you a favour.

well if the old adage is true - that like attracts like - your blue neon washer nozzles will probably attract more blue ( and red) lights - attached to a cop car haha..

man .. dont do it .. they look soooo crap and will bring shame on the house of neesan!

Hey, isn't the two neons on the centre of your car going to be annoying at night (pic in the bottom left of your sig)? The ones in the foot well look alright because you can't see the tube, but the ones on the centre?

Hey, isn't the two neons on the centre of your car going to be annoying at night (pic in the bottom left of your sig)? The ones in the foot well look alright because you can't see the tube, but the ones on the centre?

i agree to an extent though it does look kinda cool, reminds me of the gtr in 2 fast 2 furious, but that had neons all over the joint, tubes showin evrywhere,

have the cops ever hassled u about those in the center?

the ones in center are new, and they pulse to the bass of my subs

haha

distracting... not really, you think it would be but ur so focused on the road you just kinda dont notice them

and whenever i get pulled up by cops i just pull out one lil plug and all 8 neons in my car turn off

so whenever i see a cop/get pulled over out the cord goes.

but naa as far as distracting its like loud music.. you just kinda dont notice it once u start driving

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...