Jump to content
SAU Community

Recommended Posts

Going through the RB26 turbo upgrade thread it looks like most people upgrade the twin turbo set up and get great results.

What are the benefits of pulliing the two turbos out and just getting one big one?

Is this seen as a better or worse option that upgrading the two turbos or is it no difference?

Would one turbo make more power than the twin turbo set up?

Sorry for the ignorance but Im a GTR newbie trying to build up knowledge as Im seriously considering buting one in next few months.

Cheers

i think the reason behind most twin turbo upgrades apart from the obvious more power, is because it still looks factory..

so when a cop opens ur bonnet, instead of havin a 600hp massive single sittin all high and mighty, u have the same 600hp but in theyre stock locations. meaning as far as the cop knows, its a standard GTR...

plus that also means, u can use standard oil lines, water lines, dump pipes and everything else provided they are a bolt on replacement for the GTR :)

If you do your typical mods like Front mount intercooler,Tomei stage 2 cams with adj cam gears, injectors, ignition coils,exhaust turbo back, ecu usually Apexi Power Fc, and either Garret ball bearing direct spec replacement turbos to factory which i have or N1 or hks this will still give you fantastic street responce actually better than factory responce great drivability and round about 330 to 370Rwkw max depending on the engine as to how new or tired it may be getting. I still have factory air flow meters and got a 352Rwkw and i am installing the Tomei stage 2 cams now which i know yield great results as one of my close buddys has the same as me and achieved 375Rwkw with all the same mods listed, hope this helps.

its just easier to replace the twins because you can keep your exhaust manifolds and inlet piping the same. Plus, you dont have to buy an external wastegate. Replacing things like this isnt cheap

Also, the response and top end of the twin bolt ons can both be phenomenal with spool up superior to a big single due to less rotating mass/inertia

Personally, i like the idea of having a non-defectable, factory looking, 11 second street car. Not many other cars can claim to be that

Edited by SLIPPERY

If your to go the twin way, remember to do dump's and front pipe also. add that to your cost. as your alot better off to do this while the turbos are off. it will save time and money!!

I'm yet to see a justification for dump pipes. Front pipes yes - dump pipes in theory but I've never seen a difference in real life (I'm still running the standard dumps and have looked at comparitive dyno graphs with cars with the same turbo's / engine as me and there's no difference).

But thats another story.

My opinion is as above. Unless you are going REALLY big power then twins are the answer.

I'm yet to see a justification for dump pipes. Front pipes yes - dump pipes in theory but I've never seen a difference in real life (I'm still running the standard dumps and have looked at comparitive dyno graphs with cars with the same turbo's / engine as me and there's no difference).

But thats another story.

My opinion is as above. Unless you are going REALLY big power then twins are the answer.

The R34 dump pipes are great from the factory.

The R32 and R33 are significantly worse.

Go garrett and you should not be spending more than $2,500 for the turbo's alone. About $2,100 for a pair of 2560's. Greenline and Nengun are overseas mailorder traders that are only necessary if you are going with trust or hks etc. All garrett stuff is in stock in most states. For your power goals, i think the 2560's would be a great choice with nice early spool and great power potential with the right supporting mods.

except that there is none available from garret currently (-5's that is).

I have a set which haven't even been fitted yet. If my car sells (somene genuine seems interested and approached me, jyst depends on their cirtcumstances), I'll be selling them separately.

You can run 11's on the stock turbos if you can drive.

Its been done before a number of times

I would have left mine, but the factory ceramics scare me with the horror stories... I wish I could just leave with nothing hanging around in the back of my mind! Even though the car is so new, I still would rather be safe than sorry...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...