Chris Rogers Posted October 25, 2007 Share Posted October 25, 2007 R34 1 - First pull out the ashtray and undo the screw behind it. 2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin. 3 - Using a thin flat blade screwdriver on the left side, prise out the 2 vents at the top of the console and disconnect the unit. 4 - Undo the 2 silver screw at the top of the heater controls. 5 - Pull out the heater controls, radio & stage bin (all in a cage together). 6 - Remove the radio from the cage (2 screws each side) and fit your radio. 7 - Refit going from step 5 back Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/ Share on other sites More sharing options...
skybarge Posted October 25, 2007 Share Posted October 25, 2007 Nice guide here's the 32: R32 1. Pull out ashtray like below, undo two screws behind it 2. Flathead screwdriver under the rear of the center console, push up, it will pop out 3. Flathead screwdriver under the top half of center console, pops out, remove center console, or turn it around 4. Undo 4 screws, two either side of headunit, pull headunit out 5. Undo cage holding onto headunit, refit to new headunit, finish wiring off and put back in hole 6. Refit going backwards from 4 Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3435338 Share on other sites More sharing options...
DRD-00F Posted October 25, 2007 Share Posted October 25, 2007 Spose everyone has their own way Nice write up Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3435375 Share on other sites More sharing options...
n15m0 Posted October 26, 2007 Share Posted October 26, 2007 was I your guinea pig chris??? Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3436934 Share on other sites More sharing options...
Chris Rogers Posted October 26, 2007 Author Share Posted October 26, 2007 was I your guinea pig chris??? keeep it on topic guys. my intent was to get this stuck to the top so everyone would stop asking how to get them out and stop filling my PM box u jon, can't remember done too many of the things. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3437000 Share on other sites More sharing options...
Vik Posted January 27, 2008 Share Posted January 27, 2008 R33 by anychance ? Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3607223 Share on other sites More sharing options...
Chris Rogers Posted January 28, 2008 Author Share Posted January 28, 2008 (edited) R33 remove ashtray remove 3 screws unclip panel around shifter remove two more screws below radio area. unclip main surround unclip wiring from: clock,hazards,rear demist , A/C temp sensor, electric mirrors remove main surround. remove 4 screws from radio assy. unclip HVAC and radio wiring. contact me for pocket,harness and antenna adapter remove 4-8 screws from radio and put yours in place. reassemble. Edited January 28, 2008 by Chris Rogers Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3607274 Share on other sites More sharing options...
2KR34 Posted April 27, 2008 Share Posted April 27, 2008 R341 - First pull out the ashtray and undo the screw behind it. 2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin. 3 - Using a thin flat blade screwdriver on the left side, prise out the 2 vents at the top of the console and disconnect the unit. 4 - Undo the 2 silver screw at the top of the heater controls. 5 - Pull out the heater controls, radio & stage bin (all in a cage together). 6 - Remove the radio from the cage (2 screws each side) and fit your radio. 7 - Refit going from step 5 back OK I used Chris's instructions and a couple of extra things that he told me about so here is a slightly more detailed description with pics. 1 - First pull out the ashtray and undo the screw behind it. The ashtray just pulls out with no significant force needed. I just pulled on the open lid. 2 - Pull up the gear stick surround and undo the 2 silver screws at the bottom left/right of the storage bin. This takes a bit more force, I pulled from the back near the handbrake and levered it up with my fingers. I also pulled off the shift knob at this time but you could probably do it with it on but I thought it would be easier with it off. There are 2 screws at the front of the knob, put the shifter right back in low to get easier access. It takes a little bit of maneuvering to get the surround over the front of the shifter indicator and be careful not to scratch the vinyl with the hard edges of the surround. Unplug the lighter, lighter surround light and steering wheel shift switch. All plugs have a release tab, push it in or you will get real cranky trying to get em off. 3 - Using a thin flat blade screwdriver on the left side, prize out the 2 vents at the top of the console and disconnect the unit. This is the panel that houses the 2 vents and the hazard switch. I used some masking tape around the screwdriver to avoid scratching the vinyl when levering. Unplug the plug at rear. 4 - Undo the 2 silver screws at the top of the heater controls. 5 - Pull out the heater controls, radio & stage bin (all in a cage together). I put some toweling over the lower console area to avoid scratching the vinyl. 6 - Remove the radio from the cage (2 screws each side) and fit your radio. I undid a couple of extra screws to "open" up the cage a bit to allow the radio to be removed and the new one installed more easily and without scratching anything. Mine had the aerial adapter already fitted as there was already an aftermarket deck installed but the previous fitter had butchered the wiring loom so it was a bit more work to re-wire all the wires in a decent manner but if you are removing the stock deck then get the correct plug adapters and aerial adapter available from Chris or some auto outlets. I also bundle any wire slack in some padded tape to avoid any rubbing or rattling later on. 7 - Refit going from step 5 back I connected everything up and tried all deck functions before re-fitting the cage permanently just in case but luckily for me all went to plan. Hope this helps, Mark. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-3825612 Share on other sites More sharing options...
Oo oO Posted October 20, 2008 Share Posted October 20, 2008 far out! i was trying to put my head unit in a couple of months back n couldnt figure it out, its as simple of pull the vents out... damm it i love these threads! lol Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4207150 Share on other sites More sharing options...
julz2bit Posted November 23, 2008 Share Posted November 23, 2008 Life saver , Thanks for the tread see this why we should all donate money to keep these things here. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4278051 Share on other sites More sharing options...
ZFA57 Posted November 29, 2008 Share Posted November 29, 2008 (edited) awesome, got me out of the shit. couldnt figure it out myself. the top screws had me stumped. Edited November 29, 2008 by ZFA57 Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4291319 Share on other sites More sharing options...
POLICE Posted January 7, 2009 Share Posted January 7, 2009 Here's the link for the R33 headunit removal http://www.groovesystems.net/ns2500/ Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4353420 Share on other sites More sharing options...
Rucker34 Posted January 8, 2009 Share Posted January 8, 2009 this really helped me out!! I just thought i would add that to get the gear surround out it actually a little lever point for you to put a screwdriver by the handbreak at the back. i was having trouble working out how to get it off untill i spotted that. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4356857 Share on other sites More sharing options...
2manynissans Posted April 18, 2009 Share Posted April 18, 2009 Hi All, I got a Stag S2....it has oval vents BUT they don"t pop out. Does the top surround plate do the same? Thanks in advance, John C. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4541768 Share on other sites More sharing options...
Chris Rogers Posted April 18, 2009 Author Share Posted April 18, 2009 C34 start at teh gear stick panel and work up. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4541834 Share on other sites More sharing options...
chook Posted April 18, 2009 Share Posted April 18, 2009 th panel surrounding the vents with STAGEA written on it pops out, use something flat and wide at top and pry it out. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4541876 Share on other sites More sharing options...
snoopwogg Posted July 20, 2009 Share Posted July 20, 2009 Mad Thanks Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4725097 Share on other sites More sharing options...
jackdanielz Posted August 3, 2009 Share Posted August 3, 2009 might sound stupid but, how do u disconnect the plug behind (the wire connection) the car lighter, there are two of them, one is bigger than the other... seems like it would not come off however from the picture above, obviously 2KR34 can took them it off.. i just dont want to break it because i use it for a lot of thing to charge my ipod, gps, and when i left my lighter.... basically half of my life depends on it.. pls help someone its for a 34 btw cheers bly Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4747972 Share on other sites More sharing options...
nushtek Posted August 11, 2009 Share Posted August 11, 2009 wow now that is a detailed set of steps, i have been tryin to figure out mine for soo long, thanks a lot buddy, ur a life saver cheers!! Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-4761142 Share on other sites More sharing options...
skinner Posted March 7, 2010 Share Posted March 7, 2010 Sweeeeeeet! cheers. Link to comment https://www.sau.com.au/forums/topic/190825-head-unit-removal/#findComment-5121433 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now