Jump to content
SAU Community

Recommended Posts

It's on again - the annual club-member awards. These categories are separate to the track awards and will be presented at the final club meeting of 2007 - Tuesday 18th December.

This is a chance to reward those members who make that extra effort and who really make the club what it is - a true honour to acheive.

All members are eligible to vote and all members are eligable for all of following categories.

We ask that you keep your specific nominations private by sending an email to the address below. Feel free to discuss and ask questions in this thread though.

Email your nominations to: [email protected]

Nominations Close: Sunday 8 December (at the conclusion of the Show N Shine / Xmas BBQ).

Note:- I 'may' have to bring the date back a bit as the time gets closer. Will depend on timing requried to get trophies/etc organised. Will keep you posted.

-----

1. Thread of the year

What was the most memorable thread this year for you?

2. Rookie of the year

Who's come along and had a big impact in there inaugural year at SAUVIC?

3. She'll buff right out award

The annual Mines Datsun trophy – those fences can jump out at anyone!

4. Motorsport junkie

Come rain, com hail, come show or shine - who made an effort to get to events?

5. Most improved car

It's the 90210 trophy for the car that just keeps getting better and better.

6. It's not a Skyline but we still love you award

Not everyone packs an ‘R – the trophy for a member without stove-tops.

7. Photo of the year

Nominate one you've seen - or one you've taken. What celluloid masterpiece takes the prize?

If you can email the pic through, it would be appreciated.

8. The Troy S Brisby Memorial Trophy

Who was there, taking one, or two for the team - often in the shadow of greatness - on time, every time.

9. Club member of the year

The peak. The zenith. The capstone. The best of the best.

10. President's award

Awarded by the president’s discretion. Nominating for this wont do you any good.

Only one submission per member for each award.

Good luck to everyone!

Cheers,

Bec

Link to comment
https://www.sau.com.au/forums/topic/191433-2007-sau-vic-club-awards/
Share on other sites

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Photoshop is something that has been somewhat lacking this year, so we thought we would try out a new category in its place "Rookie of the Year".

Lol....care to list some of the rookies this year :D I was trying to think of some and everyone I thought of has been here a little while :blush:

Buff right out award i can think of 3 off the top of my head.

Troy@Sandown

Leewah@DECA

And Justin@PI

Justin wins by a mile!!!!

Can't top that, never seen a chop top 33 b4....

(Justin, I will delete if you find this offensive..)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...