Jump to content
SAU Community

Recommended Posts

yea I spot him all the time, he lives in my estate.

Spotted SMR33 last night as I was exiting to the freeway from Carindale...drove right past you at the lights but it as too dark to wave or anything :(

Karen says hi! :P

saw GTR R35 in the holy spirit hospital car park today! :D

as i was riding down in the lift the doors opened and like a sign from heaven there you were. and then i looked like a toss when i realised i was moaning out aloud and the others could hear me! lol lol :(

it was worth it!

Spotted JEZ42 at the Oxley roundabout today about 40mins ago. You were next to me going on to the roundabout. Unless you know my plates you wouldn't have seen me as i don't drive a skyline or a nissan for that fact anymore...

Spotted JEZ42 at the Oxley roundabout today about 40mins ago. You were next to me going on to the roundabout. Unless you know my plates you wouldn't have seen me as i don't drive a skyline or a nissan for that fact anymore...

Probably wouldn't have noticed if you were in a line, spent a bit to long at HN's and was running late. :banana:

White R32 with vielside front bar at like 620am this morning on Bribie Island Rd.

Also a nice R32 GTR on Newmarket Rd at 435 yesterday arvo

Was that you at the front of pack at the traffic lights opposite the car (holden?) dealership?

Was that you at the front of pack at the traffic lights opposite the car (holden?) dealership?

turning onto Kendron brook Rd.... yeah that was me in my mates black R33.... i have a white one but didnt drive to work that day.... I work in the harrys diner complex...

i think hes on this forum... h8 tax that is.

saw two GTR's tonight, a dark blue one on alex with and 32FTW gtr... gunmetal grey with white wheel.... also lol'd at a two tone orange and black one r32

I wasnt in my car its still at the mechanic.

If the R32 was charcole gray that was I!!!

Sorry mate was white...

Also seen a nice white R32 on the way home yesterday on the highway between D'bay rd turn off and Bounardy Rd turn off.. Plates were PEK33... Seemed like a quick car when you shot down the left lane... If on here did you see the guy in the white forrester on like 20 inch chromies? i think he was trying to race anyone he saw.... and the car was gutless as =]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...