Jump to content
SAU Community

Recommended Posts

Hi

im pretty new to the whole turbo world.

I have a Series 2 R33 GTST with pod filter, catback exhaust and turbotech boost controller.

I am running 12 psi and decided to perform a modification that was feature in the latest High Performance Imports magazine.

The modification involved cutting out 1 inch of the rubber intake pipe and installing a metal pipe in place of the rubber that was removed. This was done to ensure the rubber pipe stays all the way open during boost. According to HPI under high boost the rubber intake pipe can occassionally suck in on its self during high amounts of boost resulting in lost power.

Anyway.

As i am driving and hold my foot flat to the floor i hit 13psi and the car just backs off all of a sudden it scares the shit outta me.

What have i done??

Is this the wastegate opening??

I know the boost im running isnt safe, but if only hit 13psi twice and the car has lost all power both times. At the moment im trying to drive it on vacuum until my mechanic down tunes the boost to 10psi.

Does anyone know what i have done wrong??

Thanks

You are hitting rich and retard. The ECU richens the fuel mix and retards the timing, so you dont damage the engine. Run 10psi, much safer.

Edited by stolen_s15

EDIT - beaten to it..

it's not about safe.

it's about airflow.

R33 and over 10psi of airflow on stock ecu = rich and retard which you will feel as a bad missfire/power loss/jerking type thing.

with the FMIC it will be worse.

the air will be cooler therefore more dense which will mean it will cut out at lower revs say about "4500rpm"

you need some sort of ecu controling thing.

Cheap = SAFC

expensive and better = aftermarket programable ECU (Power FC, MICROGUESS, WOLF, etc etc)

Edited by GTST
i hit R&R the other day for the first time when i installed an tuned my ebc. freaks you out abit hey...ha i run mine on 11psi which i find safe.

yeah, it scared the absolute shit out of me.

I thought they didnt make SAFC's anymore?

might just need to get a second hand one if thats the case.

considering there is metal reinforcing on the rb25 intake pipe as it is you'd have to be running a LOT of boost...

I have seen one do it with only 260rwkw, took ages trying to work it out on the road, but a good tuner shoudl diagnose ti pretty quick on a dyno.

Edited by stolen_s15

ive found that every s and r series turbo car has the reinforcement inside the intake pipr, its not a steel tube if that what your looking for, its just a spring that winds itself arount the intake pipe

Mate of mine has a drift R32 2 door with a 25 in it and found a major power drop one night at a drift prac.... pulled into the pits and while free revving the engine the intake pipe was sucking closed.... they had a look at the pod air filter which was almost black it was that dirty... blew some compressed air through it and all was sweet again. only making 220 rwkw on 1.1 bar too so power is not so much a factor with the stock intake pipe

hmmm maybe someone took mine out, it had a pod on it when i bought it, definitely nothing in there like a spring.

I might give the steel pipe insert a crack for something to do

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...