Jump to content
SAU Community

Recommended Posts

scared of needles???

Likely this. Same kind of ignorance that will see them take an oral that shoots their liver to shit, yet continue going out getting smashed on the town every weekend...

Liver failure in 3...2...1....

most definitely has been raised before but would like to vent. what is it with guys that:

1. don't use towels on benches

2. have towels...on the floor next to them while they sweat on the bench?

I rarely use my towel, since I quite simply don't sweat when doing any weightlifting other than squats, deadlifts, or leg press. I use it to wipe my face, so no way am I wiping the bench and then my face with the same towel.

My gym does have those wet-wipes available which I'll use on machines/benches where I have sweat a little.

Fair enough if you don't sweat. But more often than not, these guys get up and have massive head/back/butt shaped sweat marks on the benches.....so disgusting.

I normally use my shirt to wipe my face......haha

My gym has vinyl bences that don't absorb sweat...and paper towels 3 metres away from anything...in the 9 years I've been going there I've never been told to bring a towel. It's a good culture (get it)!

Likely this. Same kind of ignorance that will see them take an oral that shoots their liver to shit, yet continue going out getting smashed on the town every weekend...

Liver failure in 3...2...1....

Plus with orals that are 'legal' they need a pct serm for it to last, just like the illegal type. These serms are illegal prescriptions most of the time.

Plus with orals that are 'legal' they need a pct serm for it to last, just like the illegal type. These serms are illegal prescriptions most of the time.

I wouldn't think there's such thing as an effective 'legal' oral AAS, or AAS of any kind.

PCT doesn't so much allow them to keep what they gained (because 9/10 times they're gonna lose it no matter what after they're off the steroids); it's more to kickstart their body's natural testosterone production once more so they don't whither away to semi-sterile nothingness lol

But yeah Nolvadex and Clomid are prescription drugs too, so PCT is just as 'illegal' and hard to obtain as the gear itself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...